Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Case 580SL Brake Failure and Rear Axle Diagnostics
#1
A sudden loss of braking in the Case 580 Super L backhoe is often linked to internal axle seal failure, hydraulic contamination, or worn-out brake linings. Early detection and proper inspection can prevent costly axle overhauls and ensure safe operation.
Case 580SL Backhoe Overview
The Case 580 Super L (580SL) was introduced in the mid-1990s as part of Case Construction Equipment’s long-running 580 series, which dates back to the 1960s. Known for its rugged design and ease of maintenance, the 580SL featured a 4-cylinder diesel engine, powershift transmission, and hydraulically actuated wet disc brakes. With thousands of units sold globally, it became a staple in municipal fleets, utility contractors, and agricultural operations.
Terminology Note
  • Wet Disc Brakes: Enclosed brake system using hydraulic pressure to compress friction discs submerged in oil.
  • Master Cylinder: A hydraulic pump actuated by the brake pedal to pressurize the brake circuit.
  • Parking Brake Pawl: A mechanical lock that engages the transmission or brake discs to hold the machine stationary.
  • Axle Seal: A component that prevents hydraulic oil from leaking into the brake cavity or vice versa.
  • Brake Warning Light: An indicator triggered by low pressure or fluid loss in the brake circuit.
Symptoms and Initial Observations
A 1997 Case 580SL with approximately 2,000 hours was reported to have lost braking power during a 90-minute drive home after auction purchase. Initially, the brakes functioned, but halfway through the trip, the brake warning light illuminated, and both pedals lost resistance, sinking to the floor. The parking brake also failed to engage. Additionally, the machine struggled to accelerate in fourth gear, especially on inclines.
Upon cooling down, the brakes temporarily returned to normal function, suggesting a heat-related hydraulic issue or fluid aeration.
Probable Causes and Diagnostic Steps
  • Internal axle seal failure: Hydraulic oil may leak past the piston seals into the rear axle housing, overfilling it and reducing brake pressure. Check axle oil level—if overfilled, suspect internal leakage.
  • Worn brake linings: If the friction material is completely worn, the pistons may overextend, causing fluid loss and ineffective braking. This also disables the parking brake, which relies on the same discs.
  • Damaged brake lines: External leaks from cracked or corroded lines can cause sudden pressure loss. Inspect all visible lines and fittings.
  • Hydraulic foaming: Long-distance travel at high RPM may cause aeration in the hydraulic system, especially if fluid is old or contaminated. Foamed oil reduces braking efficiency and can trigger warning lights.
  • Incorrect gear usage: Starting in fourth gear places excessive load on the drivetrain. Always begin in first or second gear and shift progressively.
Recommended Solutions
  • Drain and inspect rear axle oil for contamination or overfill. If brake fluid is present, the axle must be overhauled.
  • Replace both master cylinders and flush the brake circuit with fresh hydraulic-compatible brake fluid.
  • Inspect and replace brake linings and seals as needed. Use OEM or high-quality aftermarket kits.
  • Replace the parking brake pawl or adjust the linkage if linings are intact but engagement is weak.
  • Upgrade to synthetic hydraulic oil with anti-foaming additives if operating in extreme temperatures.
Preventive Maintenance Tips
  • Check brake pedal firmness weekly and monitor for gradual fade.
  • Inspect axle oil level monthly—sudden increases may indicate internal leaks.
  • Replace hydraulic filters every 500 hours and use only approved fluids.
  • Avoid prolonged high-speed travel without load, especially on older machines.
  • Keep a service log to track brake performance and fluid changes.
Conclusion
Brake failure on the Case 580SL is often a symptom of deeper axle or hydraulic issues. While the machine may temporarily recover after cooling, ignoring the warning signs can lead to complete brake loss and expensive repairs. With proper diagnostics, timely fluid maintenance, and attention to axle integrity, operators can extend the life of their braking system and ensure safe operation in the field.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Why Is the 4WD Not Engaging on a Case 580SN Backhoe Loader MikePhua 0 4 1 hour ago
Last Post: MikePhua
  Troubleshooting Noise in 4th Gear on a Case 580B MikePhua 0 5 1 hour ago
Last Post: MikePhua
  What Causes Rear Main Seal Failure After Hydraulic Pump Installation on a CAT 314C MikePhua 0 10 1 hour ago
Last Post: MikePhua
  Troubleshooting Shifting Issues in the Case 580B: From Neutral to Gear MikePhua 0 4 1 hour ago
Last Post: MikePhua
  Case 450 Starting Issues and Troubleshooting MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Why Is the Cluster Sprocket Loose on a Case 1830 Uniloader MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Where Is the Block Heater Cord Located on a Case 75XT Skid Steer MikePhua 0 4 2 hours ago
Last Post: MikePhua
  What Does Fault Code 3156 Mean on a Case 580 Super M Series 3 MikePhua 0 3 2 hours ago
Last Post: MikePhua
  ChatGPT said: Troubleshooting Case Backhoe Movement Issues MikePhua 0 1 2 hours ago
Last Post: MikePhua
  How to Activate and Troubleshoot Auxiliary Hydraulics on the Case 1845C Skid Steer MikePhua 0 3 2 hours ago
Last Post: MikePhua
  Case 580SL Loader Won’t Move: Troubleshooting and Solutions MikePhua 0 4 2 hours ago
Last Post: MikePhua
  Why a Case 650K Series I Dozer May Not Start After Wiring Harness Replacement MikePhua 0 8 3 hours ago
Last Post: MikePhua
  Diagnosing Basket Control Failure on a JLG 450A Boom Lift MikePhua 0 6 3 hours ago
Last Post: MikePhua
  Transmission Input Shaft Bearing Failure in the 175C: A Common Issue and Its Solutions MikePhua 0 2 3 hours ago
Last Post: MikePhua
  CAT 621D Parking Brake Not Releasing: Troubleshooting and Solutions MikePhua 0 5 3 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)