Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
CAT 515 Skidder Shifting Problems and Transmission Troubleshooting
#1
The CAT 515 skidder, a compact yet powerful forestry machine, is known for its agility in tight timber stands and its robust torque converter transmission. However, shifting issues—particularly failure to engage forward or reverse gears—can arise due to a combination of electrical faults, hydraulic pressure loss, or mechanical wear. Diagnosing these problems requires a methodical approach that considers both the control system and the transmission internals.
Machine Overview and Transmission Design
The Caterpillar 515 was introduced in the 1990s as a smaller alternative to the 525 and 535 skidders. It was designed for thinning operations and selective logging, offering a tight turning radius and a lighter footprint. The machine is powered by a CAT 3304 turbocharged diesel engine, paired with a powershift transmission that uses hydraulic pressure to engage clutch packs for forward and reverse movement.
The transmission is electronically controlled but hydraulically actuated. Gear selection is managed via a shift lever in the cab, which sends electrical signals to solenoids on the transmission valve body. These solenoids direct hydraulic pressure to the appropriate clutch packs, allowing the machine to move forward or backward.
Terminology and Key Components
  • Powershift Transmission: A type of transmission that uses hydraulic pressure to shift gears without a clutch pedal.
  • Clutch Packs: Sets of friction discs that engage to transmit power through the transmission.
  • Solenoid Valve: An electrically controlled valve that directs hydraulic fluid to engage specific clutch packs.
  • Transmission Control Valve: The hydraulic manifold that houses the solenoids and directs fluid flow.
  • Torque Converter: A fluid coupling between the engine and transmission that multiplies torque and allows smooth starts.
Common Shifting Issues and Symptoms
Operators have reported the following problems:
  • Machine starts and runs but does not move in forward or reverse
  • Engine bogs slightly when shifting into gear but no movement occurs
  • No unusual noises or grinding from the transmission
  • Hydraulic fluid level appears normal
  • Machine may move briefly and then stop
These symptoms suggest that the transmission is receiving partial engagement signals or that hydraulic pressure is insufficient to fully engage the clutch packs. In some cases, the issue is electrical—a failed solenoid, broken wire, or faulty switch. In others, internal wear or contamination may be preventing proper clutch operation.
Diagnostic Strategy and Field Testing
  1. Check Transmission Fluid
    • Ensure fluid is at the correct level and not foamy or discolored
    • Use a clean dipstick and check with the engine running and transmission warm
  2. Inspect Electrical Connections
    • Test voltage at the shift solenoids with the key on and shift lever engaged
    • Look for broken wires, corroded connectors, or loose terminals
    • Verify continuity from the shift lever to the solenoid harness
  3. Test Solenoid Function
    • Use a multimeter to check resistance across solenoid terminals (typically 10–20 ohms)
    • Apply 12V directly to the solenoid to confirm actuation
    • Listen for a click or feel for movement when energized
  4. Measure Hydraulic Pressure
    • Install a pressure gauge at the test port on the transmission valve body
    • Compare readings to factory specifications (often 200–300 psi at idle)
    • Low pressure may indicate a worn pump, clogged filter, or internal leak
  5. Inspect Control Valve and Spools
  • Remove and clean spools if sticking is suspected
  • Check for debris or varnish buildup that may restrict movement
Field Example and Resolution
A logger in northern Ontario experienced a no-move condition on his 515 after a cold morning start. The engine ran fine, but the machine would not move in any gear. After verifying fluid level and electrical continuity, he discovered that the forward solenoid had failed internally. Replacing the solenoid restored full function. He later installed a pressure gauge permanently to monitor clutch pressure during operation.
Preventive Maintenance and Recommendations
  • Change transmission fluid and filters every 1,000 hours or sooner in dusty environments
  • Inspect solenoid wiring quarterly, especially near heat sources or moving parts
  • Use dielectric grease on connectors to prevent corrosion
  • Install a pressure gauge port for quick diagnostics
  • Keep spare solenoids and fuses in the service truck for field repairs
Conclusion
Shifting problems on the CAT 515 skidder are often rooted in electrical or hydraulic faults rather than catastrophic mechanical failure. By understanding the interaction between the control system and the transmission, operators can diagnose and resolve issues quickly. With proper maintenance and a few diagnostic tools, the 515 can remain a reliable workhorse in demanding forestry operations.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Troubleshooting Hydraulic Failure on the Komatsu PC200-7 MikePhua 0 3 Yesterday, 07:57 PM
Last Post: MikePhua
  JCB 8080 Fault Code Display Issues: Troubleshooting and Solutions MikePhua 0 1 Yesterday, 07:56 PM
Last Post: MikePhua
  Bucket Cylinders on Case 590 SM: Troubleshooting and Solutions MikePhua 0 3 Yesterday, 07:50 PM
Last Post: MikePhua
  Skytrak 9038 Transmission Light Issue: Troubleshooting and Solutions MikePhua 0 1 Yesterday, 07:48 PM
Last Post: MikePhua
  Volvo 740B Hydraulic System Issues: Troubleshooting and Maintenance Tips MikePhua 0 1 Yesterday, 07:45 PM
Last Post: MikePhua
  Case 9030B Excavator: Troubleshooting Common Issues MikePhua 0 1 Yesterday, 07:44 PM
Last Post: MikePhua
  Komatsu D39E-1 Powershift: Troubleshooting Slow and Weak 3rd Gear MikePhua 0 1 Yesterday, 07:40 PM
Last Post: MikePhua
  John Deere 722CH Belt Noise: Troubleshooting and Solutions MikePhua 0 1 Yesterday, 07:38 PM
Last Post: MikePhua
  Clark R28000 Oil Check: Best Practices for Maintenance and Troubleshooting MikePhua 0 1 Yesterday, 07:36 PM
Last Post: MikePhua
  John Deere 310J Transmission Faults and Pressure Diagnostics MikePhua 0 3 Yesterday, 06:45 PM
Last Post: MikePhua
  Flat Face Hydraulic Coupler Connection Problems in Hot Weather MikePhua 0 3 Yesterday, 06:44 PM
Last Post: MikePhua
  Bobcat 323 Mini Excavator Hydraulic Function Troubleshooting MikePhua 0 3 Yesterday, 06:41 PM
Last Post: MikePhua
  Troubleshooting Thumb Circuit and Fuel Shutoff on CAT 320BL Excavators MikePhua 0 1 Yesterday, 06:40 PM
Last Post: MikePhua
  D7H Transmission Line Removal: A Detailed Guide MikePhua 0 1 Yesterday, 06:38 PM
Last Post: MikePhua
  Ignition Module Troubleshooting on Genie Z45/22 with Ford LRG-4231 Engine MikePhua 0 1 Yesterday, 06:38 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)