Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Diagnosing Power Loss in a Case 450 Dozer with the 207 Diesel Engine
#1
The Case 450 and Its Mechanical Legacy
The Case 450 crawler dozer was a popular compact grading machine throughout the 1970s and early 1980s. Powered by the Case-built 207 cubic inch diesel engine, it was widely used for residential site prep, small-scale roadwork, and utility trench backfill. With a mechanical transmission and torque converter drive, the 450 offered simplicity and reliability—but like any aging machine, performance issues can emerge that blur the line between engine and drivetrain faults.
One such issue is low power under load, especially when climbing grades or attempting to steer uphill. While the engine may start easily and idle well, symptoms like black smoke, sluggish acceleration, and stalling under load point to deeper problems.
Common Symptoms of Power Loss
Operators have reported the following:
  • Excellent cold start, even after long storage
  • Black or gray smoke under throttle, especially in neutral or while turning
  • Engine “skipping” or uneven tone at high idle
  • Loss of forward motion on inclines despite high RPM
  • No braking drag, and tracks roll freely when pushed
  • Gauges show normal oil and coolant pressure
These symptoms suggest the engine is working—but not delivering usable power to the tracks. The challenge is determining whether the fault lies in fuel delivery, engine timing, or torque converter slippage.
Fuel System and Injector Timing
The Case 207 diesel is a direct injection engine with mechanical fuel delivery. If injectors were recently replaced, but the engine still runs “sloppy,” the injection pump timing may be off. Incorrect timing can cause:
  • Incomplete combustion
  • Black smoke from unburned fuel
  • Reduced torque output
  • Erratic idle and poor throttle response
Recommendations:
  • Check injection pump timing using a dial indicator or timing marks
  • Inspect injector spray pattern and nozzle condition
  • Verify fuel pressure at the pump inlet
  • Replace fuel filters and bleed the system to remove air
A master injection pump rebuilder once noted that even a few degrees of timing error can turn a healthy diesel into a smoky, gutless machine.
Air Intake and Combustion Efficiency
Restricted airflow can mimic fuel issues. A clogged air filter or collapsed intake hose will reduce oxygen supply, leading to black smoke and poor combustion.
Checklist:
  • Remove and inspect the air filter element
  • Check for oil saturation or rodent nesting
  • Inspect intake piping for cracks or soft spots
  • Test turbocharger (if equipped) for shaft play or boost loss
On older machines, the air filter housing may be dented or misaligned, causing bypass or restriction. Replacing the filter and cleaning the housing can restore airflow and improve combustion.
Torque Converter and Transmission Pressure
If the engine revs freely but the machine stalls under load, the torque converter may be slipping. This hydraulic coupling transfers engine power to the transmission, and internal wear or fluid breakdown can reduce torque multiplication.
Key indicators:
  • Transmission pressure readings cold vs. hot
  • Loss of drive power after warm-up
  • Delayed engagement or hesitation when shifting
  • Fluid discoloration or burnt smell
Solutions:
  • Test transmission pressure at designated ports
  • Compare readings to factory specs (typically 150–250 psi)
  • Flush and replace transmission fluid with OEM-grade oil
  • Inspect torque converter for internal leakage or worn stator
One technician recalled a Case 450 that ran fine cold but lost drive after 30 minutes. The culprit was a worn torque converter seal that allowed pressure to bleed off as fluid thinned.
Engine RPM and Load Response
A tachometer is essential for diagnosing power loss. If the engine fails to reach rated RPM (usually around 2,200–2,400 rpm), or drops excessively under load, it may indicate governor issues or fuel starvation.
Steps:
  • Install a temporary tachometer if none is present
  • Record high idle RPM and stall RPM under load
  • Compare to factory specs and adjust governor linkage if needed
  • Check throttle cable for binding or misalignment
If the engine revs to spec but stalls under load, the issue is likely downstream—in the torque converter or final drives.
Final Drive and Track Resistance
While the machine may roll freely when pushed, internal resistance in the final drives can still sap power. Check for:
  • Gear oil level and condition in the final drives
  • Bearing wear or gear lash
  • Sprocket alignment and track tension
  • Unusual noise or vibration during movement
If the brakes are non-functional, ensure they are not partially engaged or dragging due to linkage failure.
Conclusion
Low power in a Case 450 dozer is often a multi-system issue. While the engine may start and idle well, black smoke, poor throttle response, and stalling under load point to fuel timing, airflow restriction, or torque converter slippage. By methodically testing each system—fuel, air, transmission, and final drives—operators can isolate the fault and restore full pushing power. In a machine built for finish grading and slope work, every ounce of torque counts—and every puff of smoke tells a story.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Chain Case Failures and Brake Pin Damage in the Case 1845C Skid Steer MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Why Is the Tachometer Reading Incorrect on the Case 580K MikePhua 0 7 1 hour ago
Last Post: MikePhua
  Why Are the Pilot Controls Failing on the Case 580 Super N MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Fixing Fan Hub Bearing Issues on Bobcat 1845C with Cummins 4B Engine MikePhua 0 6 1 hour ago
Last Post: MikePhua
  Common Head Gasket Issues on Case 580B and Solutions MikePhua 0 7 1 hour ago
Last Post: MikePhua
  Diagnosing Park Brake Release Issues on the Caterpillar D6H Dozer MikePhua 0 8 1 hour ago
Last Post: MikePhua
  Troubleshooting Fault Code 115 on the Case CX210 Excavator MikePhua 0 8 1 hour ago
Last Post: MikePhua
  Rebuilding the Hydraulic Spool Control Valve on a Case 45B Dozer MikePhua 0 4 1 hour ago
Last Post: MikePhua
  Dealing with Overheating in the Case 580K Tractor MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Troubleshooting CAT 232B: Power But Won’t Start MikePhua 0 2 1 hour ago
Last Post: MikePhua
  Diagnosing Overheating in the Komatsu PC60-7 Excavator MikePhua 0 7 1 hour ago
Last Post: MikePhua
  Diagnosing No-Start Issues on a JLG 330CRT After Alternator Replacement MikePhua 0 2 1 hour ago
Last Post: MikePhua
  Restoring and Maintaining the Case 870 Agri-King with the 336BD Engine MikePhua 0 3 2 hours ago
Last Post: MikePhua
  Removing a Seized Blade Center Pin from a TD20G Dozer MikePhua 0 5 2 hours ago
Last Post: MikePhua
  Fixing a Leaking Hand Primer Pump on the John Deere 450J Dozer MikePhua 0 1 2 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)