Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Diagnosing Power Loss in a Case 450 Dozer with the 207 Diesel Engine
#1
The Case 450 and Its Mechanical Legacy
The Case 450 crawler dozer was a popular compact grading machine throughout the 1970s and early 1980s. Powered by the Case-built 207 cubic inch diesel engine, it was widely used for residential site prep, small-scale roadwork, and utility trench backfill. With a mechanical transmission and torque converter drive, the 450 offered simplicity and reliability—but like any aging machine, performance issues can emerge that blur the line between engine and drivetrain faults.
One such issue is low power under load, especially when climbing grades or attempting to steer uphill. While the engine may start easily and idle well, symptoms like black smoke, sluggish acceleration, and stalling under load point to deeper problems.
Common Symptoms of Power Loss
Operators have reported the following:
  • Excellent cold start, even after long storage
  • Black or gray smoke under throttle, especially in neutral or while turning
  • Engine “skipping” or uneven tone at high idle
  • Loss of forward motion on inclines despite high RPM
  • No braking drag, and tracks roll freely when pushed
  • Gauges show normal oil and coolant pressure
These symptoms suggest the engine is working—but not delivering usable power to the tracks. The challenge is determining whether the fault lies in fuel delivery, engine timing, or torque converter slippage.
Fuel System and Injector Timing
The Case 207 diesel is a direct injection engine with mechanical fuel delivery. If injectors were recently replaced, but the engine still runs “sloppy,” the injection pump timing may be off. Incorrect timing can cause:
  • Incomplete combustion
  • Black smoke from unburned fuel
  • Reduced torque output
  • Erratic idle and poor throttle response
Recommendations:
  • Check injection pump timing using a dial indicator or timing marks
  • Inspect injector spray pattern and nozzle condition
  • Verify fuel pressure at the pump inlet
  • Replace fuel filters and bleed the system to remove air
A master injection pump rebuilder once noted that even a few degrees of timing error can turn a healthy diesel into a smoky, gutless machine.
Air Intake and Combustion Efficiency
Restricted airflow can mimic fuel issues. A clogged air filter or collapsed intake hose will reduce oxygen supply, leading to black smoke and poor combustion.
Checklist:
  • Remove and inspect the air filter element
  • Check for oil saturation or rodent nesting
  • Inspect intake piping for cracks or soft spots
  • Test turbocharger (if equipped) for shaft play or boost loss
On older machines, the air filter housing may be dented or misaligned, causing bypass or restriction. Replacing the filter and cleaning the housing can restore airflow and improve combustion.
Torque Converter and Transmission Pressure
If the engine revs freely but the machine stalls under load, the torque converter may be slipping. This hydraulic coupling transfers engine power to the transmission, and internal wear or fluid breakdown can reduce torque multiplication.
Key indicators:
  • Transmission pressure readings cold vs. hot
  • Loss of drive power after warm-up
  • Delayed engagement or hesitation when shifting
  • Fluid discoloration or burnt smell
Solutions:
  • Test transmission pressure at designated ports
  • Compare readings to factory specs (typically 150–250 psi)
  • Flush and replace transmission fluid with OEM-grade oil
  • Inspect torque converter for internal leakage or worn stator
One technician recalled a Case 450 that ran fine cold but lost drive after 30 minutes. The culprit was a worn torque converter seal that allowed pressure to bleed off as fluid thinned.
Engine RPM and Load Response
A tachometer is essential for diagnosing power loss. If the engine fails to reach rated RPM (usually around 2,200–2,400 rpm), or drops excessively under load, it may indicate governor issues or fuel starvation.
Steps:
  • Install a temporary tachometer if none is present
  • Record high idle RPM and stall RPM under load
  • Compare to factory specs and adjust governor linkage if needed
  • Check throttle cable for binding or misalignment
If the engine revs to spec but stalls under load, the issue is likely downstream—in the torque converter or final drives.
Final Drive and Track Resistance
While the machine may roll freely when pushed, internal resistance in the final drives can still sap power. Check for:
  • Gear oil level and condition in the final drives
  • Bearing wear or gear lash
  • Sprocket alignment and track tension
  • Unusual noise or vibration during movement
If the brakes are non-functional, ensure they are not partially engaged or dragging due to linkage failure.
Conclusion
Low power in a Case 450 dozer is often a multi-system issue. While the engine may start and idle well, black smoke, poor throttle response, and stalling under load point to fuel timing, airflow restriction, or torque converter slippage. By methodically testing each system—fuel, air, transmission, and final drives—operators can isolate the fault and restore full pushing power. In a machine built for finish grading and slope work, every ounce of torque counts—and every puff of smoke tells a story.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Diagnosing and Fixing Exhaust Popping Sounds on a 48A MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Removing a Link from a Track Chain on a Case 450 Dozer MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Diagnosing low power in a 1999 Mack RD688S with E7 VMAC III system MikePhua 0 2 1 hour ago
Last Post: MikePhua
  Troubleshooting Travel Issues on a Case 340 Skid Steer MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Case 580 Super K hazard light fuse failure and electrical diagnosis MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Case 580K fuel leak at filter head and hydraulic tank seepage MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Replacement Doors for Case 580K: A Comprehensive Guide MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Case 580B Throttle Foot Feed Return Spring Maintenance MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Case W36 Hydraulic Issues and Troubleshooting MikePhua 0 1 2 hours ago
Last Post: MikePhua
  Case 580CK with 188D stalls under load MikePhua 0 1 2 hours ago
Last Post: MikePhua
  International TD-20B Dozer and DT-429 Engine Push Rod Replacement MikePhua 0 10 Yesterday, 04:18 PM
Last Post: MikePhua
  Diagnosing Control Lag in the Simon 32' All-Terrain Scissor Lift MikePhua 0 13 Yesterday, 03:20 PM
Last Post: MikePhua
  Komatsu D37 Track Tension Loss and Adjuster Cylinder Repair MikePhua 0 10 Yesterday, 03:13 PM
Last Post: MikePhua
  Troubleshooting the Standoff Arm Issue on a 2010 Case 580M Backhoe Loader MikePhua 0 9 Yesterday, 03:12 PM
Last Post: MikePhua
  Komatsu PC120-6 Hydraulic Power Loss After Warm-Up MikePhua 0 10 Yesterday, 03:08 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: