Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Chain Case Oil Volume and Contamination Issues in the Case 1840 Skid Steer
#1
Case 1840 Skid Steer Background
The Case 1840 skid steer loader was introduced in the early 1990s as part of Case’s 1800 series, designed for compact earthmoving, material handling, and agricultural tasks. Powered by a 51-horsepower Cummins 4B diesel engine, the 1840 featured a mechanical drive system with chain-driven final drives housed in sealed compartments on either side of the machine. Known for its reliability and simplicity, the 1840 became one of Case’s best-selling skid steers, with tens of thousands of units sold across North America and Europe.
Chain Case Function and Oil Requirements
Each side of the Case 1840 contains a chain case that houses the drive chains connecting the hydraulic motors to the wheels. These compartments are lubricated with oil to reduce friction, dissipate heat, and prevent corrosion. The factory recommendation calls for approximately 6 U.S. quarts (5.7 liters) of 10W-30 engine oil per side. This oil should be changed annually or more frequently if the machine operates in wet or dirty conditions.
Terminology Clarification
• Chain Case: A sealed compartment containing the drive chains and sprockets.
• Hydraulic Motor: A motor powered by hydraulic fluid that drives the wheels via chains.
• 10W-30 Engine Oil: A multi-grade oil suitable for moderate temperature ranges, commonly used in both engines and light-duty gear systems.
• Hydraulic Reservoir: The tank that stores hydraulic fluid for the loader’s lift, tilt, and auxiliary functions.
Unexpected Oil Volume and Contamination
In some cases, operators have reported draining up to 5 gallons (19 liters) of fluid from each chain case—far exceeding the expected 6-quart fill volume. The drained fluid often appears grey, thick, and contaminated, suggesting water ingress or hydraulic oil migration.
Possible causes include:
• Water Intrusion: Rainwater or washdown entering through worn seals or cracked covers.
• Hydraulic Oil Migration: Internal leakage from the hydraulic motors into the chain case due to failed motor seals.
• Overfilling: Previous service errors or misinterpretation of fill procedures.
One operator noted that the drained fluid resembled sludge, indicating long-term contamination. Another observed that the hydraulic oil level had been dropping over time, suggesting a transfer of fluid from the hydraulic system into the chain case.
Recommended Inspection and Fill Procedure
To ensure proper chain case maintenance:
• Remove the fill plug before draining to check for overpressure or overflow
• Drain the case completely and measure the volume removed
• Inspect the fluid for water, metal particles, or hydraulic oil contamination
• Clean the case using diesel fuel or a light solvent, spinning the wheels to agitate the mixture
• Drain and repeat until the flush runs clear
• Refill with 6 quarts of clean 10W-30 oil or synthetic equivalent
Some operators in cold climates prefer 0W-40 synthetic oil for better flow at sub-zero temperatures. Others reuse clean hydraulic oil from the reservoir to reduce waste, provided it meets viscosity and cleanliness standards.
Preventive Measures and Long-Term Reliability
To prevent future contamination:
• Replace top cover gaskets and seals if water ingress is suspected
• Avoid operating in deep water or mud without proper sealing
• Monitor hydraulic fluid levels for unexplained loss
• Inspect motor seals during routine service intervals
• Keep fill ports clean and capped tightly
Field Anecdote and Practical Insight
A technician in Alberta discovered that his chain cases were overfilled due to a failed motor seal. After draining nearly 20 quarts per side, he replaced the motor seals and flushed the cases with diesel. He then refilled with synthetic oil and monitored the hydraulic reservoir for stability. The issue did not recur, and the machine returned to full service.
Another operator in New York used a motorcycle chain analogy, noting that any clean oil is better than water and mud. He emphasized the importance of sealing and annual oil changes, especially for machines stored outdoors.
Conclusion
Excess oil volume and contamination in the Case 1840 chain cases often point to water ingress or hydraulic oil migration. By understanding the system’s design and following proper inspection and fill procedures, operators can restore performance and prevent long-term damage. With regular maintenance and attention to sealing, the 1840 remains a dependable workhorse in the field.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Identifying and repairing shifting issues on a vintage Hough loader MikePhua 0 8 5 hours ago
Last Post: MikePhua
  Removing a Link from a Track Chain on a Case 450 Dozer MikePhua 0 8 5 hours ago
Last Post: MikePhua
  Troubleshooting the JCB 532 Loadall: Common Issues and Solutions MikePhua 0 10 5 hours ago
Last Post: MikePhua
  Troubleshooting Travel Issues on a Case 340 Skid Steer MikePhua 0 10 5 hours ago
Last Post: MikePhua
  Cat TH406C hydraulic overheating traced to transmission clutch slippage and cooling stack contamination MikePhua 0 10 5 hours ago
Last Post: MikePhua
  Case 580 Super K hazard light fuse failure and electrical diagnosis MikePhua 0 8 5 hours ago
Last Post: MikePhua
  Case 580K fuel leak at filter head and hydraulic tank seepage MikePhua 0 8 6 hours ago
Last Post: MikePhua
  Replacement Doors for Case 580K: A Comprehensive Guide MikePhua 0 8 6 hours ago
Last Post: MikePhua
  Case 580B Throttle Foot Feed Return Spring Maintenance MikePhua 0 7 6 hours ago
Last Post: MikePhua
  Case W36 Hydraulic Issues and Troubleshooting MikePhua 0 10 6 hours ago
Last Post: MikePhua
  Case 580CK with 188D stalls under load MikePhua 0 10 6 hours ago
Last Post: MikePhua
  Cold Weather Starting Problems in the John Deere 270 Skid Steer MikePhua 0 11 Yesterday, 03:12 PM
Last Post: MikePhua
  Troubleshooting the Standoff Arm Issue on a 2010 Case 580M Backhoe Loader MikePhua 0 9 Yesterday, 03:12 PM
Last Post: MikePhua
  Cone Crusher Performance Issues and Practical Troubleshooting MikePhua 0 10 Yesterday, 03:11 PM
Last Post: MikePhua
  Case 450 Transmission Squeal and Torque Converter Failure MikePhua 0 7 Yesterday, 03:04 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: