Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Bobcat S130 ACS 32-65 Error Code: Diagnosis and Solutions
#1
Introduction to the Bobcat S130 and ACS System
The Bobcat S130 is a compact skid-steer loader renowned for its versatility and reliability in various construction and landscaping applications. Central to its operation is the Advanced Control System (ACS), which manages the machine's lift, tilt, and drive functions. The ACS ensures smooth and responsive control, enhancing operator efficiency and safety.
Understanding the ACS 32-65 Error Code
The ACS 32-65 error code indicates an issue with the sensor supply voltage. Specifically, it occurs when the ACS controller detects that the 5-volt sensor supply voltage is either higher than 5.25 volts or lower than 4.75 volts. This voltage fluctuation can disrupt the operation of the lift and tilt functions, as the ACS relies on stable sensor inputs to control these movements.
Common Causes of Code 32-65
Several factors can lead to the 32-65 error code:
  • Faulty Sensors: Defective lift or tilt sensors can cause abnormal voltage readings.
  • Wiring Issues: Damaged or corroded wiring can lead to voltage irregularities.
  • Connector Problems: Loose or corroded connectors can disrupt the sensor supply voltage.
  • ACS Controller Malfunction: A malfunctioning ACS controller may misinterpret voltage levels.
Diagnostic Steps
To diagnose and resolve the 32-65 error code, follow these steps:
  1. Check Sensor Supply Voltage: Using a multimeter, measure the voltage on sensor supply wire 1500. The reading should be approximately 5.0 volts (± 0.25 volts). If the voltage is outside this range, proceed to the next step.
  2. Inspect Sensors Individually: Unplug each sensor one at a time—tilt handle, tilt pedal, lift handle, lift pedal, tilt actuator, and lift actuator. After disconnecting each sensor, measure the voltage on wire 1500. If the voltage returns to normal after disconnecting a particular sensor, that sensor is likely faulty and should be replaced.
  3. Conduct a Wiggle Test: With the sensors reconnected, perform a wiggle test on sensor supply wire 1500. Move the wire along its length and observe any changes in voltage. If the voltage fluctuates, it indicates a wiring issue that needs to be addressed.
  4. Check for Grounding Issues: Inspect the ACS harness for continuity to ground. If wire 1500 has continuity to ground, there is a short circuit, and the harness should be repaired or replaced.
Preventative Measures
To prevent future occurrences of the 32-65 error code:
  • Regular Maintenance: Periodically inspect sensors, wiring, and connectors for signs of wear or corrosion.
  • Proper Storage: Store the machine in a dry, sheltered environment to protect electrical components from moisture.
  • Timely Repairs: Address any issues promptly to prevent further damage to the ACS system.
Conclusion
The ACS 32-65 error code on the Bobcat S130 signifies a voltage supply issue affecting the lift and tilt functions. By systematically diagnosing the problem and addressing faulty components, operators can restore full functionality to the machine. Regular maintenance and prompt attention to electrical issues are essential to ensure the longevity and reliability of the Bobcat S130.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Bobcat 753 Hydraulic Lockup and Troubleshooting Strategy MikePhua 0 11 Yesterday, 02:59 PM
Last Post: MikePhua
  Bobcat T770 Tilt Circuit Drift and Valve Troubleshooting MikePhua 0 12 Yesterday, 02:54 PM
Last Post: MikePhua
  John Deere 850J Dozer Code TCU620.4 and Electrical Fault Tracing MikePhua 0 10 Yesterday, 02:38 PM
Last Post: MikePhua
  Bobcat T190 Cab Heater System: Troubleshooting and Maintenance MikePhua 0 12 Yesterday, 02:38 PM
Last Post: MikePhua
  John Deere 450 Transmission Problems and Practical Solutions MikePhua 0 7 Yesterday, 02:20 PM
Last Post: MikePhua
  Volvo 160C Screen Issues: Troubleshooting and Solutions MikePhua 0 4 Yesterday, 02:05 PM
Last Post: MikePhua
  Bobcat 863F Hydraulic Leaks: Common Causes and Solutions MikePhua 0 8 Yesterday, 01:58 PM
Last Post: MikePhua
  Bobcat 331 Slew Not Holding: Troubleshooting Hydraulic Issues MikePhua 0 8 Yesterday, 01:57 PM
Last Post: MikePhua
  Why Does the John Deere 310G Run Erratically with Code F494 MikePhua 0 4 Yesterday, 01:53 PM
Last Post: MikePhua
  Ford 4500 Steering Issues: Diagnosis and Solutions MikePhua 0 10 10-18-2025, 08:19 PM
Last Post: MikePhua
  Why Did the Hydraulic Motor Fail on a Bobcat FRC200XT After Just 50 Hours MikePhua 0 3 10-18-2025, 08:13 PM
Last Post: MikePhua
  Bobcat 753 Common Problems and Troubleshooting MikePhua 0 2 10-18-2025, 08:05 PM
Last Post: MikePhua
  Deere 333G Track Issues and Solutions MikePhua 0 3 10-18-2025, 08:04 PM
Last Post: MikePhua
  Kobelco Error Codes: Understanding and Troubleshooting Hydraulic Excavator Issues MikePhua 0 4 10-18-2025, 08:01 PM
Last Post: MikePhua
  Dealing with Bad Gas in Heavy Equipment: Causes and Solutions MikePhua 0 4 10-18-2025, 07:54 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: