Yesterday, 11:27 AM
Why Fuel Priming Matters on the D6D
On the Caterpillar D6D (circa 1985) equipped with the 3306 engine and a sleeve-metering injection pump, manually priming the fuel system is often essential—especially after running dry. Trapped air prevents proper fuel pressure buildup, leading to difficult starts or failure to start. The primer pump's job is to purge this air, delivering a solid fuel column into the injection system, and enabling the engine to fire.
Typical Symptom Scenario
A D6D operator struggled with fuel loss overnight. Even after running for hours, the machine wouldn't restart without repeated priming. On closer inspection, the filter housing's siphon-break was stuck open, and the governor housing contained air. After cleaning the valves and bleeding both pump and governor housing, the machine resumed trouble-free starts—even after downtime.
Practical Summary List
Starting reliability and fuel system integrity depend on a proper prime. Small leaks or air traps cause frustration and unnecessary downtime. By systematically eliminating external and internal fault points—and ensuring full venting of critical pump compartments—the D6D remains dependable and responsive when you need it most. Let me know if you’d like a visual guide to locating governor housing bleeds or diagnosing pump seal faults.
On the Caterpillar D6D (circa 1985) equipped with the 3306 engine and a sleeve-metering injection pump, manually priming the fuel system is often essential—especially after running dry. Trapped air prevents proper fuel pressure buildup, leading to difficult starts or failure to start. The primer pump's job is to purge this air, delivering a solid fuel column into the injection system, and enabling the engine to fire.
Typical Symptom Scenario
- Hand-priming allows the engine to run, but the pump doesn’t stay primed.
- Fuel appears to bleed back via the return or transfer line despite no visible external leaks.
- Operator has replaced the primer pump (likely aftermarket) and rebuilt the governor—but the issue persists.
- Aftermarket Primer Pump Concerns
Users report that non-OEM hand primer pumps often underperform or fail prematurely.
- Check Valve or Siphon-Break Blockage
The bleed valve and siphon-break device atop the fuel filter housing may be sticking or clogged. Cleaning these can restore proper airflow control and prevent unintended pressure loss.
- Internal Diaphragms and Check Valves
Persistent failure to hold prime suggests leak paths inside the pump—worn seals, diaphragms, or valves may allow fuel to return when the pump is idle.
- Governor Housing Trapped Air
Even after bleeding the main pump housing, air can remain trapped inside the governor housing. A bleed port there—often undocumented in manuals—needs to be opened to fully purge air, or cranking must compress it out.
- Check Your Primer Pump
Prefer OEM or reputable replacements. Aftermarket pumps are prone to early failure.
- Clean the Filter Housing Components
Disassemble and clean the siphon-break and constant-bleed valve. Ensure the disc moves freely.
- Inspect Internals of the Fuel Pump
If priming still fails, rebuild or replace the pump. Worn or leaking diaphragms or check valves are likely culprits.
- Bleed Governor Housing
Locate and open the bleed screw on the governor housing after topping up. This ensures no trapped air remains to disrupt priming.
- Primer Pump (Hand Pump): Manual device to purge air and pressurize fuel lines.
- Siphon-Break / Constant-Bleed Valve: Components in the filter housing intended to maintain proper vacuum or bleed conditions; they must operate freely.
- Governor Housing: Section of the injection pump containing governor springs and controls; susceptible to trapped air preventing proper priming.
A D6D operator struggled with fuel loss overnight. Even after running for hours, the machine wouldn't restart without repeated priming. On closer inspection, the filter housing's siphon-break was stuck open, and the governor housing contained air. After cleaning the valves and bleeding both pump and governor housing, the machine resumed trouble-free starts—even after downtime.
Practical Summary List
- Use an OEM-grade hand primer pump to ensure reliability.
- Clean and verify operation of bleed valve and siphon-break on filter housing.
- If priming fails, suspect internal pump components and rebuild or replace.
- Locate and bleed governor housing to eliminate trapped air and stabilize startup behavior.
- Monitor for fuel leaks and ensure fittings and seals are intact.
Starting reliability and fuel system integrity depend on a proper prime. Small leaks or air traps cause frustration and unnecessary downtime. By systematically eliminating external and internal fault points—and ensuring full venting of critical pump compartments—the D6D remains dependable and responsive when you need it most. Let me know if you’d like a visual guide to locating governor housing bleeds or diagnosing pump seal faults.
