Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
CAT 345BL Won’t Walk or Swing: Diagnosing Hydraulic and Electrical Causes
#1
Introduction
A Caterpillar 345BL excavator that starts and runs but won’t walk or swing can be frustrating and costly. Operators and mechanics often troubleshoot a combination of hydraulic and electrical issues to get the machine moving again.
Symptoms
  • Engine starts and runs normally.
  • No response from travel motors or swing motor.
  • Hydraulic pumps may still be running but with no output to these circuits.
Possible Causes
Hydraulic Control Problems
If the main control valve is stuck or a pilot line is blocked, hydraulic flow to the travel and swing circuits may be interrupted. Contaminated fluid or failed solenoids are common culprits.
Electrical or Safety Interlock Issues
Modern excavators have electronic interlocks that prevent functions if safety switches are triggered. A failed seat switch, travel lock, or a bad wiring connection can disable travel and swing.
Pump Control Failure
If the pump is not stroking properly, hydraulic pressure won’t build for the swing or travel functions. This can be caused by stuck regulators or failed sensors.
Troubleshooting Tips
  • Verify that all safety switches are functioning.
  • Inspect fuses and wiring to the control solenoids.
  • Check hydraulic pilot pressures at the control valve.
  • Inspect the control valve for stuck spools or debris.
  • Confirm pump output and look for signs of regulator issues.
Conclusion
A 345BL that won’t walk or swing is usually suffering from an electrical interlock problem, a hydraulic control valve issue, or a pump control fault. Careful inspection of both electrical and hydraulic systems is necessary to pinpoint the failure and return the machine to full operation.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Diagnosing and Recovering from Hydraulic Pump Failure on a CAT 953 MikePhua 0 3 57 minutes ago
Last Post: MikePhua
  Resolving Hydraulic Pump Leaks on the Case 1845C Skid Steer MikePhua 0 7 1 hour ago
Last Post: MikePhua
  Diagnosing and Repairing Fuel Tank Leaks on the Case 580D Backhoe MikePhua 0 4 1 hour ago
Last Post: MikePhua
  Hydraulic Fluid Level Maintenance in Case 580K MikePhua 0 7 Today, 01:15 AM
Last Post: MikePhua
  Diagnosing Fluid Leaks from the Swing Drive on a CAT 345BL MikePhua 0 5 Yesterday, 10:03 PM
Last Post: MikePhua
  Resolving Hydraulic Remote Valve Issues on the CAT 65E Challenger MikePhua 0 5 Yesterday, 06:29 PM
Last Post: MikePhua
  Dealing with Stuck Hydraulic Filters on the Takeuchi TL130: Causes and Solutions MikePhua 0 2 Yesterday, 06:28 PM
Last Post: MikePhua
  Diagnosing Track Drive Problems on the John Deere 190E MikePhua 0 5 Yesterday, 06:17 PM
Last Post: MikePhua
  Diagnosing Safety Lockout and Electrical Faults on the New Holland E18SR MikePhua 0 5 Yesterday, 06:17 PM
Last Post: MikePhua
  Kobelco SK250LC-6 Swing Issues: Troubleshooting and Solutions MikePhua 0 3 Yesterday, 06:12 PM
Last Post: MikePhua
  Caterpillar D5C Hydraulic Tank Filler Cap: Importance, Maintenance, and Replacement MikePhua 0 5 Yesterday, 05:51 PM
Last Post: MikePhua
  Diagnosing Sway Malfunction in the 1999 Terex SS1048 Telehandler MikePhua 0 3 Yesterday, 05:43 PM
Last Post: MikePhua
  Hydraulic Pump Issues on CAT 3046T Engine: Diagnosis and Solutions MikePhua 0 9 Yesterday, 04:14 PM
Last Post: MikePhua
  Diagnosing Speedometer Failure on a 1997 International 4700 MikePhua 0 8 Yesterday, 04:13 PM
Last Post: MikePhua
  Diagnosing Hydraulic Drift on the 1995 Caterpillar 938F Loader MikePhua 0 7 Yesterday, 03:46 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)