Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
IT28G Hydraulic System Issue: Slow Mast Lowering and Joystick Control Failure
#1
The user reports that the IT28G loader is experiencing slow mast lowering and cannot use the joystick to lower the mast. This issue affects the machine's efficiency, especially in tasks requiring quick mast adjustments. Slow mast movement or control failure can delay operations and impact productivity.
Common Causes
  1. Insufficient or Contaminated Hydraulic Fluid
    If the hydraulic fluid is low or contaminated, it can cause improper functioning of the hydraulic system, especially in the mast lowering and control system. Contaminants can clog the valves or damage the pump, resulting in slow or faulty mast movement.
  2. Hydraulic Pump Malfunction
    A faulty hydraulic pump is another common cause of slow mast movement. If the pump is worn out or not operating efficiently, it may not generate sufficient pressure, leading to delayed mast movement.
  3. Hydraulic Valve Issues
    Malfunctions in hydraulic control valves (such as proportional or flow control valves) can cause irregular fluid flow. Blocked or worn-out valves may fail to control the mast lowering function properly, leading to slow or erratic movement.
  4. Joystick Control System Failure
    The joystick system may have issues such as electrical faults, sensor problems, or signal transmission failures. If the joystick is not sending correct signals to the hydraulic valves, the mast will not respond to the joystick commands, preventing lowering.
  5. Hydraulic Line Leaks
    Leaking hydraulic lines can lead to reduced pressure in the hydraulic system, preventing proper fluid flow and resulting in slow mast lowering. Leaks can occur at hose connections, seals, or fittings.
Troubleshooting Steps
  1. Check Hydraulic Fluid Levels and Quality
    The first step is to check the hydraulic fluid level. Ensure the fluid is at the correct level and of good quality. If the fluid is contaminated, it should be drained and replaced with the recommended type of hydraulic oil. Also, replace any clogged filters to ensure optimal fluid flow.
  2. Inspect the Hydraulic Pump
    Check the hydraulic pump for proper functioning. Use a pressure gauge to verify if the pump is providing the necessary pressure. If the pump is malfunctioning or showing signs of wear, it may need to be repaired or replaced.
  3. Examine Hydraulic Valves and Controls
    Inspect the control valves responsible for mast movement. Look for any blockages, leaks, or signs of wear. Ensure that the joystick is sending the correct signals and that the valves are responding to these commands. Clean or replace faulty valves as needed.
  4. Check Joystick Control System
    Inspect the joystick control system for electrical issues, including wiring problems or faulty sensors. Verify that the control signals are properly transmitted from the joystick to the hydraulic valves. Use diagnostic tools to check for communication errors in the system.
  5. Inspect Hydraulic Lines for Leaks
    Check all hydraulic lines for leaks, especially around connections and fittings. Any sign of fluid leakage should be addressed immediately by tightening connections or replacing damaged hoses.
Solutions
  1. Replace or Top Up Hydraulic Fluid
    If the fluid level is low or the oil is contaminated, replace the hydraulic fluid and ensure the fluid is clean. Replace any filters to ensure proper filtration of the fluid.
  2. Repair or Replace the Hydraulic Pump
    If the hydraulic pump is found to be faulty, repair or replace it. Ensure the pump is providing sufficient pressure for the mast lowering operation.
  3. Repair or Replace Hydraulic Valves
    If the valves are blocked, damaged, or malfunctioning, clean or replace them. Ensure that the valves are properly regulating the fluid flow to the mast.
  4. Repair Joystick Control System
    If the joystick control system is malfunctioning, inspect the electrical components, wiring, and sensors. Repair or replace faulty parts to restore proper control.
  5. Fix Hydraulic Line Leaks
    Repair or replace any leaking hydraulic lines. Ensure that all connections are properly tightened to prevent further leaks and maintain optimal system pressure.
Preventive Measures
  1. Regularly Check Hydraulic Fluid Levels and Quality
    Periodically check the hydraulic fluid levels and replace the fluid as needed. Keep the fluid clean by replacing filters regularly and using high-quality oil to prevent contamination.
  2. Maintain the Hydraulic Pump and Valves
    Perform regular maintenance on the hydraulic pump and valves to ensure they are functioning properly. Inspect for wear, damage, or signs of leakage and replace parts as needed.
  3. Inspect the Joystick Control System
    Regularly inspect the joystick control system for electrical faults and ensure proper signal transmission. Replace any damaged wires or faulty sensors to avoid control issues.
  4. Inspect Hydraulic Lines and Fittings
    Regularly check hydraulic lines and fittings for signs of wear or leaks. Tighten connections and replace damaged hoses to prevent fluid loss and pressure issues.
Conclusion
When the IT28G loader experiences slow mast lowering or joystick control failure, it is essential to check the hydraulic fluid, hydraulic pump, control valves, joystick control system, and hydraulic lines. By following a thorough troubleshooting process, users can identify and resolve the issue effectively. Regular maintenance and inspections will help prevent future hydraulic system problems, ensuring smooth and efficient loader operation.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Caterpillar 225 Excavator: A Milestone in Hydraulic Excavation MikePhua 0 4 6 hours ago
Last Post: MikePhua
  Excavator Control Patterns MikePhua 0 4 6 hours ago
Last Post: MikePhua
  Choosing the Right 4x4 System Depends on Terrain and Task MikePhua 0 5 Yesterday, 02:01 PM
Last Post: MikePhua
  Bleeding the Brake System on a Case 621D Loader MikePhua 0 11 10-02-2025, 01:14 PM
Last Post: MikePhua
  Fiat-Allis 125E Charging System and Cold Start Solutions Without Ether MikePhua 0 14 10-02-2025, 01:03 PM
Last Post: MikePhua
  Flushing Water from the Hydraulic System of an International Harvester Backhoe MikePhua 0 10 10-02-2025, 12:24 PM
Last Post: MikePhua
  Doosan Hydraulic Excavators Performance Reliability and Market Impact MikePhua 0 13 10-01-2025, 03:11 PM
Last Post: MikePhua
  Drive System Challenges in the Case 440CT Compact Track Loader MikePhua 0 13 10-01-2025, 02:58 PM
Last Post: MikePhua
  The 600L Hy-Hoe Excavator and the Legacy of Hydraulic Machinery Company MikePhua 0 15 10-01-2025, 01:10 PM
Last Post: MikePhua
  Caterpillar SR321 Snow Blower Hydraulic Layout and Operational Design MikePhua 0 11 10-01-2025, 01:05 PM
Last Post: MikePhua
  Bobcat 331 and 440 Hydraulic Compatibility and Operational Insights MikePhua 0 17 10-01-2025, 12:17 PM
Last Post: MikePhua
  Hydraulic Gooseneck vs. Mechanical Detach Gooseneck Trailers: Key Differences and Considerations MikePhua 0 16 10-01-2025, 10:40 AM
Last Post: MikePhua
  Caterpillar 308D SB Excavator Performance Reliability and Hydraulic System Insights MikePhua 0 19 10-01-2025, 10:36 AM
Last Post: MikePhua
  Link-Belt 5800 Excavator Track Adjustment and Travel System Behavior MikePhua 0 17 09-30-2025, 10:17 PM
Last Post: MikePhua
  Volvo EC160BLC: Air in the Fuel System MikePhua 0 15 09-30-2025, 10:14 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: