Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Restoring Power and Hydraulic Precision on the Komatsu PC220LC-3
#1
Legacy of the PC220LC-3
The Komatsu PC220LC-3 excavator, introduced in the 1980s, was a cornerstone of mid-size earthmoving fleets across North America and Asia. With an operating weight around 22 tons and powered by a Komatsu S6D105 diesel engine, it featured a robust hydraulic system and mechanical simplicity that made it a favorite among independent contractors and municipal operators. Though long discontinued, many units remain in service today, often rebuilt and modified to extend their working life.
Turbocharger Failure and Engine Power Loss
One common issue with aging PC220LC-3 units is turbocharger failure. In a documented case, the impeller had seized, leading to low boost pressure and sluggish engine response. The turbo was replaced, restoring airflow and combustion efficiency. Operators should monitor for signs of turbo wear, including:
  • Excessive black smoke under load
  • Whistling or grinding noises
  • Oil seepage around the compressor housing
  • Reduced hydraulic performance due to engine lag
Turbochargers on these machines typically operate at 80,000 to 120,000 rpm and rely on clean oil and balanced exhaust flow. Replacing a failed unit with a remanufactured or OEM turbo can restore 15–25% of lost engine power.
Hydraulic Pump Rebuild and TVC Adjustment
The PC220LC-3 uses a twin-pump hydraulic system with a TVC (Throttle Valve Control) mechanism that links engine throttle position to hydraulic output. After rebuilding the pumps, the operator noticed that the arm function—specifically in and out movement—was slow and loaded the engine excessively.
This symptom often points to misadjusted TVC linkage or internal spool wear. The TVC system modulates pump displacement based on throttle input, ensuring that hydraulic demand matches available engine power. If the TVC is out of sync, the pump may overdraw, causing engine bogging or sluggish implement response.
Steps to Diagnose and Correct Arm Function Lag
  • Inspect the TVC cable and linkage for binding or misalignment
  • Adjust the TVC lever to match throttle position at idle and full stroke
  • Check pump output pressure with gauges at the arm circuit
  • Verify spool valve movement and spring tension
  • Clean or replace hydraulic filters to ensure unrestricted flow
In one case, adjusting the TVC restored normal engine behavior, but arm speed remained slow. This led to further inspection of the arm cylinder seals and flow control valves, revealing internal leakage that reduced effective stroke speed.
Additional Considerations for Legacy Machines
Older excavators like the PC220LC-3 may suffer from:
  • Worn control valve spools causing delayed response
  • Contaminated hydraulic fluid reducing pump efficiency
  • Electrical issues in throttle sensors or solenoids
  • Cracked hoses or fittings introducing air into the system
Routine maintenance should include:
  • Hydraulic fluid analysis every 500 hours
  • TVC calibration during annual service
  • Cylinder seal inspection every 1,000 hours
  • Turbocharger boost pressure testing during engine tune-ups
Conclusion
Restoring full function to a Komatsu PC220LC-3 requires a blend of mechanical insight and hydraulic diagnostics. Turbocharger replacement can resolve power loss, but slow arm movement often points to TVC misadjustment or internal hydraulic wear. With careful calibration and component inspection, even “old school” machines can deliver reliable performance in modern jobsite conditions. These excavators remain a testament to durable engineering and the value of hands-on troubleshooting.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Hydraulic Fluid Level Maintenance in Case 580K MikePhua 0 6 2 hours ago
Last Post: MikePhua
  Resolving Hydraulic Remote Valve Issues on the CAT 65E Challenger MikePhua 0 5 9 hours ago
Last Post: MikePhua
  Dealing with Stuck Hydraulic Filters on the Takeuchi TL130: Causes and Solutions MikePhua 0 2 9 hours ago
Last Post: MikePhua
  Understanding and Troubleshooting Komatsu 830E Brake Pressure Faults MikePhua 0 6 9 hours ago
Last Post: MikePhua
  Can the Modulator Valve Be Repaired on a Komatsu D21A-7 MikePhua 0 5 9 hours ago
Last Post: MikePhua
  Caterpillar D5C Hydraulic Tank Filler Cap: Importance, Maintenance, and Replacement MikePhua 0 5 9 hours ago
Last Post: MikePhua
  Restoring a White Lift Forklift and Solving Rear-End Clearance Issues MikePhua 0 5 9 hours ago
Last Post: MikePhua
  Restoring Charge Pressure in the Clark HR328 Transmission on a TJ450A Skidder MikePhua 0 6 10 hours ago
Last Post: MikePhua
  Hydraulic Pump Issues on CAT 3046T Engine: Diagnosis and Solutions MikePhua 0 9 11 hours ago
Last Post: MikePhua
  Diagnosing Hydraulic Drift on the 1995 Caterpillar 938F Loader MikePhua 0 7 11 hours ago
Last Post: MikePhua
  What If You Forget the Komatsu PC290LC Ignition Security Password MikePhua 0 11 Yesterday, 03:11 PM
Last Post: MikePhua
  Komatsu PC300-7 Hydraulic Fault: Troubleshooting and Solutions MikePhua 0 10 Yesterday, 03:09 PM
Last Post: MikePhua
  Diagnosing Hydraulic and Electrical Failure in a Hitachi EX200-2 MikePhua 0 5 Yesterday, 03:00 PM
Last Post: MikePhua
  Komatsu D39P-1 Valve Pinging or Engine Knock: A Detailed Exploration MikePhua 0 11 Yesterday, 02:02 PM
Last Post: MikePhua
  Resolving Intermittent Hydraulic Slowdown on the Hitachi EX100-3 MikePhua 0 12 Yesterday, 01:58 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)