Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Why a CAT D4H Dozer May Suddenly Stop Moving Despite Normal Hydraulic Pressure
#1
CAT D4H Dozer Overview
The Caterpillar D4H is a mid-size crawler dozer introduced in the 1980s and produced into the early 1990s. It features an elevated sprocket design, a powershift transmission, and a modular drivetrain layout. Powered by a CAT 3304 turbocharged diesel engine producing approximately 100 horsepower, the D4H was widely adopted for grading, land clearing, and light construction. With an operating weight of around 20,000 pounds and a reputation for reliability, it remains a common sight on job sites and farms.
Caterpillar’s elevated sprocket design, first introduced in the D6H, improved undercarriage serviceability and reduced shock loads to the final drives. The D4H was offered in multiple configurations, including standard, LGP (low ground pressure), and Series II variants.
Symptoms of Sudden Drive Loss
A recurring issue with aging D4H units is the sudden inability to move in any gear, despite normal engine operation and hydraulic pressure. Common symptoms include:
  • No driveshaft rotation in forward, reverse, or neutral
  • Transmission temperature rising rapidly within minutes
  • Engine lugging slightly when in gear or neutral
  • Driveshaft briefly spins when both track brake levers are pulled in neutral
  • Transmission control lever feels normal, with detents intact
These symptoms suggest a failure in the transmission clutch packs or a blockage in the lubrication circuit, rather than a final drive lockup or external brake issue.
Terminology Notes
  • Driveshaft: The shaft connecting the transmission output to the bevel gear and final drives.
  • Clutch Pack: A set of friction and steel plates used to engage gears in a powershift transmission.
  • Lube Pressure: Hydraulic pressure dedicated to lubricating internal transmission components.
  • Park Brake Valve: A hydraulic spool that controls brake engagement; often located below the shifter.
Root Cause and Diagnostic Path
In one documented case, the transmission had been rebuilt less than 100 hours prior. After a day of operation, the machine stopped moving with a faint pop. A CAT technician confirmed normal hydraulic pressures except for zero lube pressure. The driveshaft remained stationary in all positions, and the transmission overheated quickly.
Pulling both brake levers in neutral caused the driveshaft to spin briefly and restored engine idle speed, suggesting that hydraulic flow was being redirected or relieved. This behavior pointed to a seized clutch pack or blocked lube circuit.
Upon disassembly, the transmission revealed catastrophic internal damage. A thrust washer had been omitted during the previous rebuild, causing misalignment and seizure of one clutch pack. The transmission was rebuilt again, and the issue resolved.
Additional Considerations
  • Park Brake Linkage Contamination: Dirt buildup under the park brake valve can prevent full brake release, causing drag and transmission strain. Cleaning with a long blowgun is recommended.
  • Final Drive Lockup: While possible, this would not prevent driveshaft rotation in neutral. Removing axle shafts can isolate the final drives for testing.
  • Hydraulic Safety Systems: Some operators speculate about automatic brake lockup due to low fluid, but CAT dozers do not use such systems. Brake drag from low pressure is possible but would be accompanied by other symptoms.
Recommendations for Technicians and Owners
  • Check Lube Pressure First: Zero lube pressure is a red flag for internal transmission failure.
  • Inspect Park Brake Valve Linkage: Clean and verify full travel to prevent drag.
  • Test Driveshaft in Neutral: It should rotate if clutch #3 is engaged and torque converter is functioning.
  • Avoid Long-Term Storage Without Service: Seals may dry out, and fluid contamination can accelerate failure.
  • Document Rebuilds Thoroughly: Missing thrust washers or misaligned clutch packs can destroy a transmission in hours.
Final Thoughts
A CAT D4H that suddenly stops moving despite normal hydraulic pressure likely suffers from internal transmission failure, often due to clutch pack seizure or lube circuit blockage. While external brake drag and final drive issues should be ruled out, the key diagnostic indicator is driveshaft behavior in neutral. With proper inspection and attention to rebuild detail, the D4H remains a serviceable and reliable machine for decades.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Replacing a Hydraulic Pump: A Guide to Identifying and Addressing Common Issues MikePhua 0 6 36 minutes ago
Last Post: MikePhua
  Why Does a 1979 CAT D3 Dozer Lose Drive When Steering Is Applied MikePhua 0 3 37 minutes ago
Last Post: MikePhua
  How Do You Replace the Bucket Hydraulic Hose on a CAT 304C CR MikePhua 0 3 41 minutes ago
Last Post: MikePhua
  How Do You Access and Replace Speed Sensors on a John Deere 750C Dozer MikePhua 0 9 58 minutes ago
Last Post: MikePhua
  Why Won’t the Starter Engage Properly on an International TD15C Dozer MikePhua 0 10 59 minutes ago
Last Post: MikePhua
  What Causes Rear Main Seal Failure After Hydraulic Pump Installation on a CAT 314C MikePhua 0 10 1 hour ago
Last Post: MikePhua
  Why Does the CAT 950B Loader Lose Brakes Intermittently Despite Full Air Pressure MikePhua 0 7 1 hour ago
Last Post: MikePhua
  CAT 305D: Common Hydraulic and Performance Issues MikePhua 0 9 1 hour ago
Last Post: MikePhua
  Why Do Steering Accumulators on CAT 789C Haul Trucks Lose Pressure After Servicing MikePhua 0 2 1 hour ago
Last Post: MikePhua
  How to Read and Diagnose Fault Codes on a CAT D6N Dozer MikePhua 0 1 1 hour ago
Last Post: MikePhua
  How to Add an Auxiliary Control Valve to a CAT D6R Dozer Without Compromising Steering Priority MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Troubleshooting Service Code Issues on the CAT D6RXL Dozer MikePhua 0 7 1 hour ago
Last Post: MikePhua
  How to Plumb a Hydraulic Thumb and Hammer on a Kobelco SK230SRLC-3 Efficiently MikePhua 0 3 1 hour ago
Last Post: MikePhua
  What Happens When Diesel Is Accidentally Added to Hydraulic Oil MikePhua 0 7 1 hour ago
Last Post: MikePhua
  How to Fix a Final Drive Oil Leak on the CAT D6B Dozer MikePhua 0 7 2 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)