Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Bobcat 753 Skid Steer Stalling After Running for a Few Minutes
#1
The Bobcat 753 is a highly capable and compact skid steer loader known for its reliability in a variety of construction and landscaping tasks. However, like any piece of heavy equipment, the 753 can experience operational problems. One such issue is when the machine starts and runs for a short period, maybe five minutes, before stalling unexpectedly. This issue can be frustrating, but understanding the possible causes and solutions can help operators diagnose and resolve the problem efficiently.
Common Causes of Stalling in the Bobcat 753
Stalling after a brief period of operation is often caused by a variety of factors, ranging from fuel system problems to electrical issues. Identifying the root cause is crucial for implementing the appropriate fix.
1. Fuel System Issues
One of the most common causes of stalling in the Bobcat 753 is a problem with the fuel system. A fuel delivery issue can prevent the engine from receiving a consistent supply of fuel, causing the machine to run for a short period before cutting out.
  • Potential Causes:
    • Clogged Fuel Filter: Over time, fuel filters can become clogged with dirt and debris, restricting the flow of fuel to the engine. A dirty or clogged fuel filter can result in intermittent fuel delivery, causing the engine to stall after running for a while.
    • Fuel Pump Failure: The fuel pump is responsible for moving fuel from the tank to the engine. If the fuel pump is failing or malfunctioning, it may not deliver a consistent supply of fuel, leading to stalling after a few minutes of operation.
    • Contaminated Fuel: If the fuel in the tank has water or dirt contamination, it can cause improper combustion and result in stalling. This is especially common if the machine has been stored for a while or has been used in environments where fuel contamination is a risk.
  • Solution: Check and replace the fuel filter regularly to prevent clogging. If the fuel filter looks clean, test the fuel pump to ensure it is operating correctly. Drain and replace contaminated fuel if necessary, and inspect the fuel lines for leaks or blockages.
2. Electrical Problems
Another potential cause of stalling could be an issue with the electrical system. The Bobcat 753 relies on electrical components like the alternator, battery, and fuses to keep the engine running. If any of these components fail or malfunction, it can cause the machine to stall unexpectedly.
  • Potential Causes:
    • Faulty Alternator: If the alternator is not charging the battery properly, the electrical system may lose power after a few minutes of operation, leading to stalling. The alternator is responsible for keeping the battery charged while the engine is running, so if it fails, the engine may cut out once the battery's power is depleted.
    • Weak Battery: A battery with low charge or one that is near the end of its lifespan can cause the machine to lose power and stall. If the battery is unable to supply the necessary voltage, the engine may struggle to keep running.
    • Wiring Issues: Loose, corroded, or damaged wiring can prevent the electrical system from functioning correctly. A poor connection can interrupt the flow of electricity to vital components, including the ignition system, resulting in stalling.
  • Solution: Test the alternator and replace it if it is not charging the battery effectively. Ensure the battery is fully charged and in good condition. Check all wiring for signs of wear or corrosion and repair or replace any damaged parts.
3. Ignition System Malfunctions
A malfunction in the ignition system can also cause the Bobcat 753 to stall after a few minutes. If the ignition system is not delivering the correct spark to the engine, it may cause the engine to stop running after starting.
  • Potential Causes:
    • Faulty Ignition Coil: The ignition coil generates the spark needed for combustion. If the coil is malfunctioning, the engine may start but will not be able to sustain operation.
    • Defective Spark Plug: A worn or defective spark plug can cause intermittent ignition failure. When this happens, the engine may start but then stall shortly after, as the spark plug is unable to create a consistent spark.
    • Ignition Switch Problems: The ignition switch sends power to the ignition system. If it is failing or malfunctioning, it may intermittently cut off the engine's power, leading to stalling.
  • Solution: Inspect the ignition coil for signs of damage or wear and replace it if necessary. Check the spark plugs for wear or fouling, and replace them if they are damaged or dirty. Test the ignition switch to ensure it is functioning correctly.
4. Air Intake Blockages
A blockage in the air intake system can cause the engine to stall by restricting the airflow needed for proper combustion. The engine relies on a steady flow of air to mix with the fuel for ignition. If the air intake is obstructed, the engine may not run properly and could stall after a short period.
  • Potential Causes:
    • Clogged Air Filter: Over time, air filters accumulate dust, dirt, and debris, reducing the airflow to the engine. A clogged filter can cause the engine to run rich (too much fuel) and lead to stalling.
    • Obstructions in the Air Intake Path: If there is a blockage anywhere in the intake system, it will prevent the engine from getting enough air, causing it to stall.
  • Solution: Inspect the air filter regularly and replace it if it is dirty or clogged. Clean the air intake system and ensure there are no obstructions preventing proper airflow.
5. Overheating
While overheating is less common than other issues, it can still cause the Bobcat 753 to stall. If the engine temperature rises too high, it can cause the engine to shut down to prevent damage.
  • Potential Causes:
    • Low Coolant Levels: If the coolant level is low, the engine may overheat, leading to stalling as a safety measure.
    • Coolant System Failure: A malfunctioning water pump or radiator can cause the engine to overheat.
  • Solution: Check the coolant levels and top them up as needed. Inspect the cooling system for leaks or signs of failure, and repair any damaged components.
Preventative Maintenance Tips
To reduce the likelihood of experiencing stalling issues with your Bobcat 753, here are some key maintenance practices:
  • Regularly Change the Fuel Filter to ensure consistent fuel flow.
  • Check the Battery and Alternator to ensure they are charging and holding power properly.
  • Inspect and Clean the Air Filter to prevent blockages that can affect engine performance.
  • Keep the Cooling System in Good Condition by regularly checking coolant levels and inspecting the system for leaks.
  • Perform Regular Oil Changes to keep the engine running smoothly.
Conclusion
The Bobcat 753 is a reliable piece of machinery, but like any heavy equipment, it can experience issues that impact its performance. Stalling after a few minutes of operation is often caused by fuel system problems, electrical malfunctions, ignition system issues, air intake blockages, or overheating. By understanding the potential causes and implementing regular maintenance practices, operators can prevent stalling and ensure their Bobcat 753 continues to perform optimally for years to come. Regular checks, prompt repairs, and the use of high-quality parts will help extend the machine’s lifespan and reduce downtime.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Resolving ECM Faults and Safety Lockouts on a CAT 277B Skid Steer MikePhua 0 1 Less than 1 minute ago
Last Post: MikePhua
  Lift Pump Issues in Bobcat 743: Common Causes and Solutions MikePhua 0 3 5 hours ago
Last Post: MikePhua
  Troubleshooting Uneven Buckets on Skid Steers and Loaders MikePhua 0 6 5 hours ago
Last Post: MikePhua
  ChatGPT said: Troubleshooting Fuel Problems on the Gehl 4840 Skid Steer MikePhua 0 8 5 hours ago
Last Post: MikePhua
  Why Do the Lift Arms on a Bobcat T595 Drift Down When Closing the Grapple MikePhua 0 7 5 hours ago
Last Post: MikePhua
  Where Is the Block Heater Cord Located on a Case 75XT Skid Steer MikePhua 0 4 5 hours ago
Last Post: MikePhua
  Bobcat 863 Side Steer: Troubleshooting No Power and Starting Issues MikePhua 0 1 5 hours ago
Last Post: MikePhua
  Why the Bobcat S205 May Shut Down When Attempting to Move MikePhua 0 4 5 hours ago
Last Post: MikePhua
  How to Activate and Troubleshoot Auxiliary Hydraulics on the Case 1845C Skid Steer MikePhua 0 3 6 hours ago
Last Post: MikePhua
  Troubleshooting New Holland L785 Skid Steer: No Go, No Start, No Fun MikePhua 0 5 6 hours ago
Last Post: MikePhua
  Diagnosing Swing Circle Rattling on a Bobcat 320 Mini Excavator MikePhua 0 5 6 hours ago
Last Post: MikePhua
  Why a CAT 287B Skid Steer May Fail to Start Despite Power at the Battery MikePhua 0 8 7 hours ago
Last Post: MikePhua
  Why Is the Dipstick Blowing Out on a Bobcat 863 with Deutz 1101F Engine MikePhua 0 3 7 hours ago
Last Post: MikePhua
  Bobcat T250 Hydraulic Failure and Tandem Drive Catastrophe MikePhua 0 10 8 hours ago
Last Post: MikePhua
  Troubleshooting a Non-Starting New Holland LX865 Skid Steer MikePhua 0 10 8 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)