Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Why Does Track Speed Decrease on Komatsu Excavators Over Time
#1
Komatsu excavators often experience gradual track speed loss due to aging hydraulic components, particularly weakened valve springs in the load-sensing system. This issue is more common in older models like the PC120-3, PC130-6, and PC160-7, and can be corrected through hydraulic tuning and valve recalibration.
Komatsu excavator lineage and hydraulic architecture
Komatsu has produced a wide range of excavators since the 1960s, with the PC series becoming globally recognized for reliability and performance. The PC120-3 (1989), PC130-6 (1999), and PC160-7 (2004) represent three generations of mid-sized excavators, each with evolving hydraulic systems:
  • PC120-3: Open-center load-sensing hydraulics with mechanical control
  • PC130-6: Transition to closed-center hydraulics with improved efficiency
  • PC160-7: Electronically modulated closed-center system with better responsiveness
All three rely on variable-displacement piston pumps and load-sensing valves to adjust flow based on demand. Over time, these valves can drift from factory settings due to spring fatigue, contamination, or wear.
Symptoms and operational patterns
Operators often report:
  • Sluggish tracking after warm-up
  • Reduced travel speed compared to earlier performance
  • No fault codes or warning lights
  • Normal boom and arm function
These symptoms typically emerge after 5,000–7,000 hours of operation and worsen gradually. In some cases, the machine performs well when cold but loses speed as hydraulic oil heats up.
Root causes and mechanical explanation
The primary cause is spring fatigue in the load-sensing valves. These springs regulate the position of spools that control pump output. As they weaken:
  • Valve response slows
  • Pump output decreases under load
  • Travel motors receive less flow
  • Track speed drops, especially under resistance
Older open-center systems (Dash 3 and Dash 5) are more sensitive to spring wear and require periodic tuning. Closed-center systems (Dash 6 and Dash 7) are more stable but still degrade over time.
Diagnostic method and performance benchmark
A simple field test involves measuring boom lift cycle time:
  • Extend stick and open bucket fully
  • Place all implements on the ground
  • Set engine to full throttle and mode to high
  • Time the boom lift from ground to full stroke
A healthy system should complete the lift in around 4 seconds. If it takes 5 seconds or more, the hydraulic system likely needs adjustment.
Additional contributing factors
  • Undercarriage wear: Worn rollers or sprockets increase friction
  • Hydraulic oil degradation: Old fluid loses viscosity and cooling capacity
  • Contaminated filters: Restrict flow and reduce pump efficiency
  • Operator adaptation: Skilled operators may outpace the machine’s response, perceiving it as slow
One technician in Malaysia noted that bottom rollers not sticking properly can also contribute to perceived speed loss, especially on uneven terrain.
Recommended solutions and maintenance strategy
  • Recalibrate load-sensing valves to factory spec
  • Replace weakened springs in valve bodies
  • Flush and replace hydraulic oil every 2,000 hours
  • Inspect and replace hydraulic filters
  • Check undercarriage components for resistance
  • Monitor travel motor pressure and flow rates
For older machines, a full hydraulic tune-up every 5,000 hours can restore performance and prevent further degradation.
Conclusion
Track speed loss in Komatsu excavators is a known issue tied to hydraulic valve wear and system aging. With proper diagnostics and recalibration, performance can be restored. Understanding the interplay between hydraulic architecture, mechanical wear, and operator expectations is key to maintaining long-term efficiency.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Troubleshooting the Two-Speed Motor Issue on the MTL 25 Tak TL 150 MikePhua 0 5 59 minutes ago
Last Post: MikePhua
  How Do You Access and Replace Speed Sensors on a John Deere 750C Dozer MikePhua 0 9 1 hour ago
Last Post: MikePhua
  Converting a Komatsu PC75UU-2 Offset Boom to a Standard One-Piece Boom MikePhua 0 11 1 hour ago
Last Post: MikePhua
  Komatsu D21A-6 Powershift Hesitation: Diagnosing and Solving Shifting Delays MikePhua 0 11 1 hour ago
Last Post: MikePhua
  Repairing a Cracked Track Frame on the CAT D6H Dozer MikePhua 0 6 2 hours ago
Last Post: MikePhua
  Troubleshooting Slow Left Track Movement on the KX91-2 Mini Excavator MikePhua 0 7 2 hours ago
Last Post: MikePhua
  Troubleshooting Speed Range Control Sensor Faults on the CAT 972M MikePhua 0 5 2 hours ago
Last Post: MikePhua
  Finding Reliable Mechanic Services for Excavators in North New Jersey MikePhua 0 5 3 hours ago
Last Post: MikePhua
  Why the Auxiliary Hydraulics and Speed Control Fail on CAT 287B MikePhua 0 2 3 hours ago
Last Post: MikePhua
  Isuzu Diesel Engine No-Start Issues in IHI 30NX Excavators MikePhua 0 4 4 hours ago
Last Post: MikePhua
  Komatsu PC200-7 Hydraulic Failure and Pilot Pressure Troubleshooting MikePhua 0 7 4 hours ago
Last Post: MikePhua
  Quick Hitch Ram Issues on Komatsu WA380-6: Troubleshooting and Solutions MikePhua 0 4 4 hours ago
Last Post: MikePhua
  Komatsu TB1140 Troubleshooting and Maintenance Guide MikePhua 0 9 4 hours ago
Last Post: MikePhua
  Track Tension Failure on IH TD-15C and Idler Seal Replacement Strategy MikePhua 0 9 5 hours ago
Last Post: MikePhua
  Troubleshooting Forward Speed and Power Issues in the Volvo EW140 MikePhua 0 9 5 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)