Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Voltage Drop and Boom Failure in Genie Z60/34 Diesel Lifts
#1
Quick answer
A Genie Z60/34 with a diesel engine may experience boom function failure due to low charging voltage, weak ground connections, or alternator drag caused by a failing fuel shutoff solenoid. Voltage below 13.8V at operating RPM is insufficient for full system performance.
Genie Z60/34 overview and electrical system
The Genie Z60/34 is a diesel-powered articulating boom lift designed for elevated work in construction, maintenance, and industrial settings. It features:
  • A Deutz FL2011 engine (varies by year)
  • Dual boom sections with hydraulic articulation
  • Ground and basket control stations
  • 12V electrical system with alternator charging
The lift relies on stable voltage to power solenoids, sensors, and control logic. Voltage drop can disable boom functions while leaving other systems operational.
Symptoms and diagnostic clues
In one case, the primary and secondary booms failed to respond, while other functions remained intact. Applying an external battery charger temporarily restored boom operation. A new battery did not resolve the issue. Alternator output was measured at 13.4V.
This behavior suggests:
  • Charging voltage too low: Most systems require 14.2–14.5V under load
  • Voltage drop at control station: Basket voltage may be lower than ground-level readings
  • Grounding issues: Corroded or loose engine ground can reduce system voltage
  • Alternator drag: A failing fuel shutoff solenoid may draw excessive current
Alternator and wiring inspection
The Deutz FL2011 engine may use either an internal or external alternator. For internal types:
  • Remove the side panel above the dipstick and fuel pump
  • Measure voltage at the alternator output terminal and starter hot post
  • Clean and reattach the engine ground strap
  • Inspect the excite wire plug near the alternator cover
For external alternators:
  • Check belt tension and pulley alignment
  • Test voltage at idle and full throttle
  • Confirm regulator function and diode integrity
If voltage remains below 13.6V after cleaning grounds and checking connections, rebuild or replace the alternator.
Fuel shutoff solenoid and parasitic draw
A failing fuel shutoff solenoid can drag down alternator output. Symptoms include:
  • Engine stalling or hard starting
  • Excessive current draw during operation
  • Alternator overheating
To test:
  • Disconnect the solenoid and measure voltage recovery
  • Check resistance across solenoid terminals
  • Replace if resistance is low or draw exceeds spec
Voltage at basket controls
Voltage drop between ground-level and basket controls is common due to:
  • Long wire runs
  • Corroded connectors
  • Undersized conductors
Measure voltage at the basket during boom activation. If below 12.5V, inspect harness and connectors. Consider installing a voltage booster or relay to stabilize control power.
Recommendations for resolution
  • Clean and inspect all ground points, especially engine block and frame
  • Measure voltage at alternator, starter, and basket controls
  • Test fuel shutoff solenoid for parasitic draw
  • Rebuild alternator if voltage remains below 13.8V
  • Use a battery charger only as a diagnostic aid, not a permanent fix
Conclusion
Boom failure in the Genie Z60/34 often stems from low system voltage caused by alternator inefficiency, poor grounding, or parasitic draw. By restoring proper charging voltage and verifying control circuit integrity, full boom function can be recovered without replacing major components.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Converting a Komatsu PC75UU-2 Offset Boom to a Standard One-Piece Boom MikePhua 0 11 1 hour ago
Last Post: MikePhua
  What Causes Rear Main Seal Failure After Hydraulic Pump Installation on a CAT 314C MikePhua 0 10 1 hour ago
Last Post: MikePhua
  Troubleshooting Slow Starting in 12.7 Detroit Diesel Engines MikePhua 0 8 2 hours ago
Last Post: MikePhua
  How to Remove Stuck Diesel Injectors Without Damaging the Cylinder Head MikePhua 0 1 2 hours ago
Last Post: MikePhua
  What Happens When Diesel Is Accidentally Added to Hydraulic Oil MikePhua 0 7 2 hours ago
Last Post: MikePhua
  Troubleshooting Hissing Noise from Boom Cylinder on Caterpillar 345BL MikePhua 0 6 2 hours ago
Last Post: MikePhua
  CAT 303CR Boom Swing Stuck: Troubleshooting and Solutions MikePhua 0 4 2 hours ago
Last Post: MikePhua
  Diagnosing EFI Faults on the Ford LRG-425 Engine in JLG Boom Lifts MikePhua 0 4 3 hours ago
Last Post: MikePhua
  Diagnosing Basket Control Failure on a JLG 450A Boom Lift MikePhua 0 6 3 hours ago
Last Post: MikePhua
  Transmission Input Shaft Bearing Failure in the 175C: A Common Issue and Its Solutions MikePhua 0 2 3 hours ago
Last Post: MikePhua
  Isuzu Diesel Engine No-Start Issues in IHI 30NX Excavators MikePhua 0 4 4 hours ago
Last Post: MikePhua
  Komatsu PC200-7 Hydraulic Failure and Pilot Pressure Troubleshooting MikePhua 0 7 4 hours ago
Last Post: MikePhua
  Genie S-60 Platform Leveling and Troubleshooting MikePhua 0 4 4 hours ago
Last Post: MikePhua
  Track Tension Failure on IH TD-15C and Idler Seal Replacement Strategy MikePhua 0 9 5 hours ago
Last Post: MikePhua
  John Deere 35D Spool Valve Failure and Hydraulic Plug Repair Options MikePhua 0 10 5 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)