Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Why Does My Gehl Loader Tilt But Not Lift
#1
Gehl 4835 Loader Overview
The Gehl 4835 skid steer loader was introduced in the late 1990s as part of Gehl’s compact equipment lineup. Designed for construction, landscaping, and agricultural use, the 4835 featured a robust hydraulic system, mechanical controls, and a rated operating capacity of approximately 1,500 lbs. Powered by a diesel engine and equipped with a two-function joystick or T-bar control, it allowed operators to manage both lift and tilt functions through a spool valve assembly. Gehl, founded in Wisconsin in 1859, became known for its durable compact loaders before merging into the Manitou Group in the 2000s.
Symptoms of Hydraulic Lift Failure
A common issue reported by operators is that the loader arms fail to lift or lower, while the tilt function continues to work normally. This behavior often mimics the machine’s safety lockout mode, where the lift circuit is disabled when the seat switch, safety bar, or parking brake is engaged. However, if tilt remains functional, the issue likely lies elsewhere.
In one case, the operator could hear the hydraulic system attempting to engage the lift function, but the arms remained stationary. This ruled out complete hydraulic failure and pointed toward an electrical or solenoid-related fault.
Safety Interlock System and Diagnostic Clues
The Gehl 4835 uses a multi-point safety interlock system:
  • Seat switch: Disables all hydraulic functions when the operator leaves the seat
  • Safety bar switch: Disables lift when the bar is raised
  • Parking brake switch: Disables both lift and tilt when engaged
If tilt works but lift does not, the seat and parking brake switches are likely functioning correctly. The issue may be isolated to the lift solenoid or its control circuit.
Solenoid and Relay Configuration
The hydraulic valve body beneath the cab includes two 12V coil solenoids—one for lift and one for tilt. These are mounted on the spool valve and activated by the control handles. Wires leading to the solenoids are typically white and yellow, and may be routed through relays connected to the ignition switch.
Common failure points include:
  • Loose or corroded connectors
  • Damaged solenoid coil
  • Faulty relay or fuse
  • Broken wire near the control linkage
One technician noted that the lift solenoid on his older Gehl was wired directly to the key switch. When the wires shifted slightly, the lift function failed until repositioned.
Testing and Repair Recommendations
To diagnose the issue:
  • Lift the cab and inspect the valve body
  • Trace the wires from the control handle to the solenoids
  • Test voltage at the lift solenoid during activation
  • Swap solenoids to see if the fault follows the component
  • Check relays and fuses near the instrument panel or under the seat
If the lift solenoid is receiving power but not activating, it may need replacement. If no power is present, trace the circuit back to the relay and switch.
Replacement solenoids are available from Gehl dealers or aftermarket suppliers. Installation requires removing the coil from the valve body and replacing the O-rings to prevent leaks.
Conclusion
When a Gehl 4835 loader tilts but won’t lift, the issue is often electrical—related to the lift solenoid, its wiring, or associated relays. By systematically testing the safety switches, solenoid voltage, and control circuits, operators can isolate the fault and restore full hydraulic function. With its straightforward design and accessible components, the 4835 remains a serviceable and reliable machine for small-scale operations.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Restoring a 1966 Caterpillar 955L Track Loader MikePhua 0 1 3 hours ago
Last Post: MikePhua
  Diagnosing Steering Shake in the CAT 980B Wheel Loader MikePhua 0 3 5 hours ago
Last Post: MikePhua
  Rebuilding the Loader Control System on a 1974 Case 580B CK MikePhua 0 6 Yesterday, 01:09 AM
Last Post: MikePhua
  O&K L25 Loader Overview and Common Issues MikePhua 0 6 10-11-2025, 07:53 PM
Last Post: MikePhua
  Boom Suspension Issues in Volvo L180F Wheel Loader MikePhua 0 7 10-11-2025, 06:21 PM
Last Post: MikePhua
  Track Replacement and Undercarriage Renewal on a Crawler Loader MikePhua 0 2 10-11-2025, 06:20 PM
Last Post: MikePhua
  Forward Drive Weakness on Case 580K Phase 1 Loader MikePhua 0 6 10-11-2025, 06:15 PM
Last Post: MikePhua
  Restoring and Maintaining the Dresser 515 Loader MikePhua 0 2 10-11-2025, 05:47 PM
Last Post: MikePhua
  Troubleshooting A/C Wiring Failures in the Komatsu WA380 Loader MikePhua 0 16 10-10-2025, 05:35 PM
Last Post: MikePhua
  Diagnosing Gear Shift Failures on the Hyundai HL757-7 Loader MikePhua 0 10 10-10-2025, 04:27 PM
Last Post: MikePhua
  Troubleshooting Air Seat Failure on the John Deere 744K Wheel Loader MikePhua 0 10 10-10-2025, 03:59 PM
Last Post: MikePhua
  JLG Industries 4x2x2 Scissor Lift Model 33-RTS: Understanding the Key Features and Troubleshooting MikePhua 0 11 10-10-2025, 03:59 PM
Last Post: MikePhua
  Replacing Blade Tilt Hoses on the John Deere 650J Dozer MikePhua 0 10 10-10-2025, 03:22 PM
Last Post: MikePhua
  Hydraulic Filter Service on the CAT 980K Loader MikePhua 0 13 10-10-2025, 01:41 PM
Last Post: MikePhua
  Terex 72-31 Loader Maintenance and Legacy MikePhua 0 8 10-10-2025, 01:39 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)