Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Hitachi Exhaust Delete Kit Installation and System Integration
#1
Hitachi’s Emissions Strategy and the Rise of Delete Kits
Hitachi Construction Machinery, founded in 1970, has long been a global leader in hydraulic excavator design. As emissions regulations tightened across North America and Europe in the 2010s, Hitachi began integrating Diesel Particulate Filters (DPF), Selective Catalytic Reduction (SCR), and Exhaust Gas Recirculation (EGR) systems into its mid- and large-frame excavators. These systems, while effective at reducing NOx and soot emissions, introduced complexity, increased maintenance demands, and raised operating costs.
In response, aftermarket developers introduced exhaust delete kits—electronic emulators designed to bypass or disable emissions components without altering the engine’s core programming. These kits became popular among operators in non-regulated zones or those facing repeated failures of DPF and DEF systems.
Core Components of the Delete Kit
A typical Hitachi exhaust delete kit includes:
  • Plug-and-play emulator module
  • Matching OEM-style connectors for DPF and SCR sensors
  • CAN bus interface for ECU communication
  • DEF tank signal emulator
  • NOx sensor bypass circuit
  • Installation guide and wiring diagram
The emulator mimics the signals of a fully functional emissions system, allowing the engine control unit (ECU) to operate without triggering fault codes or limp mode. It does not modify fuel maps or timing curves, preserving engine integrity.
Installation Procedure and Key Steps
Installing the delete kit on a Hitachi excavator equipped with an Isuzu engine (e.g., 4HK1 or 6WG1) involves:
  • Disconnecting the original DPF and SCR sensor plugs
  • Connecting the emulator’s matching plugs to the same harness points
  • Removing the DEF tank fuse to disable fluid injection
  • Securing the emulator module in a vibration-free location
  • Verifying CAN bus communication with the ECU
  • Starting the machine and checking for fault codes or warning lights
No cutting or splicing is required. The emulator uses factory-style connectors to ensure non-invasive installation. In one field case, a ZX210LC-5 excavator was retrofitted in under 45 minutes with no diagnostic errors post-installation.
System Behavior After Deletion
Once installed, the emulator performs the following functions:
  • Simulates DEF fluid level and pressure
  • Emulates NOx sensor readings within acceptable thresholds
  • Prevents regeneration cycles and soot accumulation alerts
  • Disables EGR valve actuation if included
  • Maintains full throttle and torque output without derate
Operators report smoother throttle response, reduced fuel consumption, and elimination of DEF-related downtime. However, the physical DPF must be removed or hollowed to prevent backpressure buildup.
Legal and Regulatory Considerations
Exhaust delete kits are intended for off-road use in non-regulated environments. In jurisdictions governed by EPA or EU emissions laws, their use may violate compliance standards. Operators should:
  • Confirm local emissions exemptions for agricultural or mining use
  • Avoid use on public roads or government-funded projects
  • Retain original components for potential reinstallation
  • Document installation for warranty or resale purposes
In 2021, a fleet in Alberta retrofitted 12 Hitachi units for oilfield use under provincial exemptions, reducing maintenance costs by 38% over 18 months.
Troubleshooting and Support Tips
If the emulator fails to communicate or triggers fault codes:
  • Check all plug connections for seating and corrosion
  • Verify fuse removal and power supply continuity
  • Use a diagnostic tool to confirm CAN bus activity
  • Contact the vendor’s tech support for firmware updates
  • Reinstall original plugs to isolate hardware faults
A technician in New Zealand resolved a persistent NOx fault by replacing a damaged emulator harness and updating the module’s firmware via USB.
Performance Gains and Operator Feedback
Operators report several benefits post-installation:
  • Fuel savings of 5–12% depending on workload
  • Elimination of DEF refills and regeneration downtime
  • Improved cold start reliability
  • Reduced sensor-related fault codes
  • Lower exhaust temperatures and simplified maintenance
In a demolition project in Texas, a ZX490LCH-6 excavator equipped with a delete kit ran 1,200 hours without a single emissions-related fault, outperforming its stock counterpart in uptime and fuel economy.
Conclusion and Recommendations
Hitachi exhaust delete kits offer a practical solution for operators facing frequent emissions system failures or operating in exempt zones. With proper installation and documentation, these kits restore machine reliability and reduce operating costs without compromising engine safety.
Recommendations include:
  • Confirm engine model compatibility before purchase
  • Follow installation steps precisely and avoid wire splicing
  • Remove or bypass physical DPF to prevent backpressure
  • Use diagnostic tools to verify system status post-installation
  • Retain original components for future compliance needs
With thoughtful integration, the delete kit transforms emissions complexity into operational simplicity—keeping Hitachi excavators productive and responsive across demanding job sites.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Cooling System Troubles on the Case 1840 Skid Steer MikePhua 0 1 Less than 1 minute ago
Last Post: MikePhua
  Fuel System Troubles on Komatsu Machines MikePhua 0 1 5 minutes ago
Last Post: MikePhua
  Hitachi EX-75UR Error E51 Troubleshooting MikePhua 0 1 42 minutes ago
Last Post: MikePhua
  Exhaust Temperature Issues and DOC Faults on the John Deere 650K MikePhua 0 1 42 minutes ago
Last Post: MikePhua
  Troubleshooting Hydraulic System Issues in Case 888, 1088, and 1288 Tractors MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Hitachi EX35-2 Starting Issues and Troubleshooting MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Case 1840 Loader Troubleshooting Hydraulic and Drive System Failures MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Komatsu FB10RS-12 Error Code 20 Diagnosis and Electrical System Recovery MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Flushing the Hydraulic System After a Bad Cylinder: Why It's Necessary and How to Do It MikePhua 0 1 2 hours ago
Last Post: MikePhua
  CAT 953 Track Loader Steering and Drive System Troubleshooting MikePhua 0 1 3 hours ago
Last Post: MikePhua
  Battery Leakage in Bobcat Equipment and Electrical System Protection MikePhua 0 1 3 hours ago
Last Post: MikePhua
  Water Contamination in Hydraulic Fluid and System Recovery Strategies MikePhua 0 1 3 hours ago
Last Post: MikePhua
  John Deere 690ELC Wiring Harness Restoration and Electrical System Reliability MikePhua 0 1 3 hours ago
Last Post: MikePhua
  FC-4000 Forklift Alarm Behavior and Electrical System Diagnosis MikePhua 0 1 3 hours ago
Last Post: MikePhua
  Bobcat T190 Reverse Speed Imbalance and Drive System Diagnosis MikePhua 0 2 3 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)