1 hour ago
The Legacy of MDI Yutani in Excavator Manufacturing
MDI Yutani was a Japanese-American joint venture that produced hydraulic excavators during the 1980s and early 1990s, primarily for the North American market. Known for robust steelwork and straightforward mechanical systems, their machines were often favored by contractors who valued durability over digital sophistication. The MD120B LC was one of their mid-size models, designed for general excavation, trenching, and light demolition. With an operating weight in the 12-ton class, it competed with machines from Komatsu, Hitachi, and early Caterpillar hydraulic lines.
Though MDI Yutani eventually exited the market, their machines remain in use, especially in rural fleets and owner-operator setups. Parts support has become more challenging, but many components were sourced from common suppliers, making refurbishment possible with cross-referenced parts.
Terminology Notes
While exact factory specs for the MD120B LC are scarce, typical parameters for machines in this class include:
Pin and Bushing Wear and Replacement Strategy
One of the most common service needs on aging excavators is the replacement of boom pins and bushings. These components wear due to:
Challenges in Parts Identification and Sourcing
Because MDI Yutani ceased production decades ago, parts manuals often lack dimensional data. Service manuals are more useful but harder to find. Key challenges include:
Recommendations for Owners and Restorers
The MDI Yutani MD120B LC excavator may be a relic of a bygone brand, but its mechanical simplicity and solid construction make it a viable machine for those willing to invest in restoration. With careful measurement, creative sourcing, and a methodical approach, owners can extend the life of these machines well beyond their original service window. In a world of increasingly complex electronics, the MD120B LC stands as a reminder that steel, hydraulics, and craftsmanship still have a place on the jobsite.
MDI Yutani was a Japanese-American joint venture that produced hydraulic excavators during the 1980s and early 1990s, primarily for the North American market. Known for robust steelwork and straightforward mechanical systems, their machines were often favored by contractors who valued durability over digital sophistication. The MD120B LC was one of their mid-size models, designed for general excavation, trenching, and light demolition. With an operating weight in the 12-ton class, it competed with machines from Komatsu, Hitachi, and early Caterpillar hydraulic lines.
Though MDI Yutani eventually exited the market, their machines remain in use, especially in rural fleets and owner-operator setups. Parts support has become more challenging, but many components were sourced from common suppliers, making refurbishment possible with cross-referenced parts.
Terminology Notes
- LC (Long Carriage): Indicates an extended undercarriage for improved stability and lifting capacity.
- Boom Pins and Bushings: Pivot components that allow the boom to articulate while absorbing load stress.
- Service Manual: A technical document detailing tolerances, torque specs, hydraulic pressures, and repair procedures.
- Parts Manual: A catalog of components with part numbers but typically lacking dimensional data.
While exact factory specs for the MD120B LC are scarce, typical parameters for machines in this class include:
- Operating weight: approx. 12,000–13,500 kg
- Engine: 4-cylinder diesel, likely Isuzu or Mitsubishi sourced
- Net power: approx. 90–110 hp
- Bucket capacity: 0.5–0.7 m³
- Max dig depth: 5.5–6.2 meters
- Track width: 500 mm
- Hydraulic pressure: 280–300 bar
Pin and Bushing Wear and Replacement Strategy
One of the most common service needs on aging excavators is the replacement of boom pins and bushings. These components wear due to:
- Repeated load cycles
- Lack of lubrication
- Contamination from dust and water
- Misalignment from frame flex or collision
- Excessive play in boom or stick
- Hydraulic drift during lifting
- Audible knocking under load
- Uneven bucket wear
- Removing hydraulic cylinders and linkages
- Pressing out worn bushings using a hydraulic press
- Measuring bore diameter and selecting oversized bushings if needed
- Installing new pins with anti-seize compound
- Greasing all joints and verifying alignment
Challenges in Parts Identification and Sourcing
Because MDI Yutani ceased production decades ago, parts manuals often lack dimensional data. Service manuals are more useful but harder to find. Key challenges include:
- Identifying correct pin diameters and lengths
- Matching bushing outer diameter and wall thickness
- Locating hydraulic seal kits for obsolete cylinders
- Finding sprockets and rollers with compatible bolt patterns
- Reverse-engineering worn parts using calipers and micrometers
- Cross-referencing with similar models from Komatsu or Kobelco
- Contacting legacy dealers who may retain microfiche archives
- Searching salvage yards and online marketplaces for donor machines
Recommendations for Owners and Restorers
- Document all part dimensions during disassembly
- Use digital calipers and bore gauges for accurate measurements
- Keep a log of cross-referenced parts and suppliers
- Replace all pins and bushings in a joint assembly to maintain balance
- Inspect hydraulic lines and fittings during mechanical repairs
The MDI Yutani MD120B LC excavator may be a relic of a bygone brand, but its mechanical simplicity and solid construction make it a viable machine for those willing to invest in restoration. With careful measurement, creative sourcing, and a methodical approach, owners can extend the life of these machines well beyond their original service window. In a world of increasingly complex electronics, the MD120B LC stands as a reminder that steel, hydraulics, and craftsmanship still have a place on the jobsite.
