Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Removing a Stuck Hydraulic Ram
#1
Introduction
Hydraulic rams, or cylinders, are integral components in various machinery, from construction equipment to industrial presses. Over time, these rams may become stuck due to factors like corrosion, debris, or internal pressure. Properly removing a stuck hydraulic ram requires a systematic approach to ensure safety and prevent damage to the equipment.
Understanding the Hydraulic Ram
A hydraulic ram operates by converting hydraulic energy into linear mechanical force. It consists of a cylinder barrel, piston, rod, gland, and seals. The piston moves within the barrel, driven by hydraulic fluid, to perform tasks such as lifting, pushing, or pulling. Common applications include excavators, loaders, and presses.
Common Causes of a Stuck Hydraulic Ram
Several factors can cause a hydraulic ram to become stuck:
  • Corrosion: Moisture and contaminants can lead to rust inside the cylinder, causing the piston to seize.
  • Debris: Dirt or metal shavings can obstruct the movement of the piston.
  • Internal Pressure: Residual hydraulic pressure can keep the piston extended or retracted.
  • Seal Failure: Damaged seals can cause internal friction, hindering movement.
Safety Precautions
Before attempting to remove a stuck hydraulic ram, ensure the following safety measures:
  • Depressurize the System: Relieve all hydraulic pressure by operating the control valves.
  • Lockout/Tagout: Implement lockout/tagout procedures to prevent accidental activation.
  • Personal Protective Equipment (PPE): Wear safety goggles, gloves, and steel-toed boots.
  • Work Area: Ensure the work area is clean and well-lit.
Step-by-Step Removal Process
  1. Preparation:
    • Clean the exterior of the hydraulic ram to remove dirt and debris.
    • Place a catch pan beneath the ram to collect any residual hydraulic fluid.
  2. Disconnect Hydraulic Lines:
    • Use appropriate tools to disconnect the hydraulic hoses from the ram.
    • Cap or plug the open ports to prevent contamination.
  3. Remove Mounting Pins:
    • Use a hammer and punch to remove any retaining pins securing the ram to the equipment.
    • Keep the pins and hardware in a safe place for reinstallation.
  4. Extract the Ram:
    • If the ram is stuck in the extended position, use a come-along or chain hoist to apply gentle force to retract it.
    • If stuck in the retracted position, apply heat to the cylinder barrel using a torch to expand the metal and loosen the ram.
    • Always apply heat evenly and avoid overheating, which can damage seals and other components.
  5. Disassemble the Ram:
    • Once removed, secure the ram in a vice.
    • Remove the gland nut using a spanner wrench or pipe wrench.
    • Extract the piston and rod assembly.
    • Inspect all components for wear or damage.
Reassembly and Testing
  • Clean Components: Thoroughly clean all parts using a suitable solvent.
  • Replace Seals: Install new seals to ensure proper function.
  • Lubricate: Apply clean hydraulic oil to all moving parts.
  • Reassemble: Reverse the disassembly steps to reassemble the ram.
  • Test: Reinstall the ram onto the equipment and test its operation under low pressure before full use.
Troubleshooting Tips
  • Persistent Sticking: If the ram remains stuck despite applying force, inspect for internal corrosion or debris.
  • Seal Damage: Damaged seals can cause internal friction; replace them promptly.
  • Uneven Heating: When applying heat, ensure even distribution to prevent warping or seal damage.
Conclusion
Removing a stuck hydraulic ram requires patience, the right tools, and adherence to safety protocols. By following the outlined steps and precautions, you can effectively address this issue and maintain the functionality of your equipment. Always consult the equipment's manual for specific instructions and seek professional assistance if needed.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Dealing with Slow Lift and Overheating Hydraulic Oil in Bobcat 75 XT MikePhua 0 1 7 minutes ago
Last Post: MikePhua
  Removing a Link from a Track Chain on a Case 450 Dozer MikePhua 0 1 8 minutes ago
Last Post: MikePhua
  Dealing with Excessive Hydraulic Fluid in Heavy Equipment MikePhua 0 1 12 minutes ago
Last Post: MikePhua
  Takeuchi TB240CRA screen failure and hydraulic claw diagnosis MikePhua 0 4 15 minutes ago
Last Post: MikePhua
  JCB 550-170 Loadall hydraulic failure traced to vibration damper and bevel box coupling MikePhua 0 3 20 minutes ago
Last Post: MikePhua
  Cat TH406C hydraulic overheating traced to transmission clutch slippage and cooling stack contamination MikePhua 0 3 20 minutes ago
Last Post: MikePhua
  Case 580K fuel leak at filter head and hydraulic tank seepage MikePhua 0 3 30 minutes ago
Last Post: MikePhua
  Bobcat 721 Hydraulic Problems MikePhua 0 1 31 minutes ago
Last Post: MikePhua
  Case W36 Hydraulic Issues and Troubleshooting MikePhua 0 1 59 minutes ago
Last Post: MikePhua
  JD319D hydraulic system fails to engage MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Komatsu PC120-6 Hydraulic Power Loss After Warm-Up MikePhua 0 10 Yesterday, 03:08 PM
Last Post: MikePhua
  Bobcat 753 Hydraulic Lockup and Troubleshooting Strategy MikePhua 0 11 Yesterday, 02:59 PM
Last Post: MikePhua
  Hitachi EX120-2 Hydraulic Conversion Kit Installation MikePhua 0 10 Yesterday, 02:55 PM
Last Post: MikePhua
  Case 580B CK Differential Lock Stuck on Brake Housing MikePhua 0 9 Yesterday, 02:37 PM
Last Post: MikePhua
  Hydraulic Issues in Caterpillar D5N Track-Type Tractors MikePhua 0 7 Yesterday, 02:26 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: