Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Cat 962M Intermittent Steering & Hydraulic Pressure Loss
#1
Overview of the Symptom
A Cat 962M wheel loader began experiencing sudden loss of steering and a sharp drop in hydraulic pressure—from around 3,848 kPa down to approximately 2,400 kPa—accompanied by a distinct whistling sound. Interestingly, the issue would temporarily resolve either if the operator shut down and restarted the engine or shook the bucket. Upon further sleuthing, the operator discovered that turning the steering from center to right lock and back to center triggered the pressure drop, while the same action to the left did not reproduce the issue.
Possible Causes
  • Pressure Relief Valve (PRV) or Spool Valve Hold-Up
    A sticking relief valve or misbehaving spool valve could cause intermittent pressure loss. A stuck PRV might vent pressure unexpectedly, while a jammed spool valve could block flow in one direction (like right turn) but not in the opposite.
  • Electronic Control Sensor Malfunction
    Since the Cat 962M uses an electro-hydraulic steering system, the malfunction may lie in a spool position sensor, a failed solenoid, or related wiring, causing the system to misinterpret steering commands.
  • Electrical/Electronic Faults
    Though no fault codes are currently active, it's possible a transient fault has occurred or a sensor is failing intermittently. Monitoring with diagnostic tools may reveal intermittent errors.
Recommended Diagnostic Steps
  • Hook up Cat Electronic Technician (ET) diagnostic software to monitor live sensor data and fault memory. Look for anomalies in steering position, pump pressure, or transient faults.
  • Perform a controlled test while logging data:
    • From center to right lock and back, observe pressure behavior in real-time.
    • Repeat to the left lock and back to confirm the asymmetry.
  • Visually and audibly inspect hydraulic lines, valves, reliefs, and pump during the fault to catch clues (e.g., pressure relief exhaust, whining, or cavitation sounds).
  • If possible, swap or test sensors/solenoids, particularly those tied to spool positioning, to isolate a possible electrical miscue.
Best Maintenance Practices for Steering Hydraulics
  • Routine system checks: Inspect hydraulic fluid levels, filter condition, and overall cleanliness. Contaminants or low fluid can cause erratic hydraulic behavior.
  • Valve and PRV service: Relief valves can stick from gumming, particle debris, or wear—especially where intermittent faults clear after jarring. Spool valves can similarly seize.
  • Diagnostic tool use: Logging pressure, sensor, and operational data during failure is key. Without logged data, intermittent issues often evade resolution.
Real-World Examples
Operators in cold regions have reported similar pressure loss issues when valves stick due to condensation or poor fluid maintenance. One fleet in Canada found that steering valve spools stuck only when turning right due to wear pattern skewed by traffic flow, a problem resolved by swapping valve blocks and updating hydraulic filtration.
Key Takeaways
  • Intermittent pressure loss on one steering direction usually suggests valve or sensor anomalies rather than pump failure.
  • Use diagnostic software during operation to gather accurate data.
  • Test sensors, relief valves, and spool positioning to pinpoint malfunction.
  • Prevent recurrence by maintaining hydraulics, filtering fluids, and servicing key components regularly.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Dealing with Slow Lift and Overheating Hydraulic Oil in Bobcat 75 XT MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Dealing with Excessive Hydraulic Fluid in Heavy Equipment MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Takeuchi TB240CRA screen failure and hydraulic claw diagnosis MikePhua 0 4 1 hour ago
Last Post: MikePhua
  JCB 550-170 Loadall hydraulic failure traced to vibration damper and bevel box coupling MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Cat TH406C hydraulic overheating traced to transmission clutch slippage and cooling stack contamination MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Case 580K fuel leak at filter head and hydraulic tank seepage MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Bobcat 721 Hydraulic Problems MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Case W36 Hydraulic Issues and Troubleshooting MikePhua 0 1 2 hours ago
Last Post: MikePhua
  JD319D hydraulic system fails to engage MikePhua 0 1 2 hours ago
Last Post: MikePhua
  Komatsu D37 Track Tension Loss and Adjuster Cylinder Repair MikePhua 0 10 Yesterday, 03:13 PM
Last Post: MikePhua
  Komatsu PC120-6 Hydraulic Power Loss After Warm-Up MikePhua 0 10 Yesterday, 03:08 PM
Last Post: MikePhua
  ChatGPT said: Caterpillar 953A Steering Troubleshooting MikePhua 0 9 Yesterday, 03:04 PM
Last Post: MikePhua
  Bobcat 753 Hydraulic Lockup and Troubleshooting Strategy MikePhua 0 11 Yesterday, 02:59 PM
Last Post: MikePhua
  Hitachi EX120-2 Hydraulic Conversion Kit Installation MikePhua 0 10 Yesterday, 02:55 PM
Last Post: MikePhua
  Low Fuel Pressure in John Deere 331G Skid Steer Loaders MikePhua 0 9 Yesterday, 02:31 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)