Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Oil Blow-By from Breather Hose on Kubota D1402 in Mustang 342 Loader
#1
The Mustang 342 and Its Kubota Powerplant
The Mustang 342 skid steer loader was a compact workhorse built during the late 1970s and early 1980s, often powered by the Kubota D1402 diesel engine. This naturally aspirated 3-cylinder engine was widely used in agricultural and industrial equipment due to its simplicity, reliability, and ease of service. With a displacement of 1.4 liters and a reputation for cold-start durability, the D1402 became a favorite among small loader manufacturers and tractor builders alike.
However, as these engines age, internal wear and poor maintenance can lead to symptoms that are easily misdiagnosed—one of the most alarming being oil discharge from the crankcase breather hose after warm-up.
Understanding the Breather System and Blow-By
The breather hose on a diesel engine vents crankcase pressure generated by piston movement and combustion gases that leak past the rings—a phenomenon known as blow-by. Normally, this pressure is minimal and the breather releases only vapor or trace oil mist. But when the engine warms up and oil begins to spew from the breather, it signals excessive blow-by or crankcase pressurization.
Common causes include:
  • Worn piston rings allowing combustion gases into the crankcase
  • Scored cylinder walls reducing sealing efficiency
  • Clogged or restricted breather system causing pressure buildup
  • Diluted or overfilled oil increasing vapor carryover
  • Failed head gasket allowing combustion pressure into the oil galleries
In the case of the D1402, oil “puking” from the breather after warm-up suggests that the engine’s internal sealing has deteriorated—most likely due to ring wear or cylinder scoring.
Diagnostic Steps and Field Observations
To confirm the source of the issue:
  • Perform a compression test on all three cylinders. Healthy readings should exceed 350 psi.
  • Remove the oil fill cap while running and observe for pulsing or vapor—excessive pressure indicates blow-by.
  • Inspect the breather hose for obstructions or sludge buildup.
  • Check oil level and condition—fuel dilution or overfilling can exacerbate the problem.
  • Look for oil contamination in the coolant or vice versa, which may suggest a head gasket failure.
One technician noted that after replacing the rings and honing the cylinders, the breather discharge stopped entirely. Another observed that a clogged breather filter caused oil to back up and exit through the hose under pressure.
Engine Rebuild vs. Temporary Fixes
If compression is low and blow-by is confirmed, a rebuild is often the only long-term solution. This typically includes:
  • New piston rings
  • Cylinder honing or re-sleeving
  • Valve guide inspection and replacement
  • Head gasket and seal replacement
  • Oil pump inspection and timing gear check
Temporary fixes may include:
  • Installing an oil catch can to prevent environmental mess
  • Cleaning or replacing the breather assembly
  • Switching to a heavier oil grade (e.g., SAE 30 or 15W-40) to reduce vaporization
  • Reducing engine load and RPM to minimize pressure buildup
However, these are stopgap measures. If the engine is used daily or under load, internal repair is inevitable.
Historical Context and Engine Longevity
The Kubota D1402 was part of a family of engines that powered everything from compact tractors to generators. Its design emphasized mechanical simplicity—no turbocharger, no electronic controls, and minimal emissions hardware. Many units ran for 5,000–8,000 hours before requiring overhaul, provided oil changes and valve adjustments were performed regularly.
In one documented case, a D1402 in a vineyard sprayer ran for 9,200 hours before the rings failed. The owner had used non-detergent oil and skipped valve lash checks for years. After a full rebuild, the engine returned to service and ran another 4,000 hours before retirement.
Recommendations for Owners of Aging Kubota Engines
To extend engine life and prevent breather issues:
  • Change oil every 100–150 hours with high-quality diesel-rated oil
  • Adjust valve lash every 500 hours
  • Clean breather and PCV components annually
  • Monitor crankcase pressure and compression during routine service
  • Avoid overloading the engine or running at max RPM for extended periods
If oil begins to discharge from the breather, act quickly. Continued operation under these conditions can lead to oil starvation, bearing damage, and eventual engine seizure.
Conclusion
Oil blow-by from the breather hose on a Kubota D1402 in a Mustang 342 loader is a clear sign of internal wear—most likely worn rings or cylinder scoring. While temporary solutions may reduce the mess, only a proper rebuild will restore performance and reliability. In machines built for hard work and long hours, the breather hose is more than a vent—it’s a warning light in disguise.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Error 8000 on O&K L15.5 Loader and Wheel Pump Diagnostics MikePhua 0 6 5 hours ago
Last Post: MikePhua
  Caterpillar 950GC Breather Filter Steam Issue MikePhua 0 5 5 hours ago
Last Post: MikePhua
  Is It Safe to Blow Down Fuel Tanks with Compressed Air MikePhua 0 6 5 hours ago
Last Post: MikePhua
  Kubota SVL 95-2 Two-Speed Not Working MikePhua 0 7 5 hours ago
Last Post: MikePhua
  Safely Removing the Belly Pan on a CAT 963C Track Loader MikePhua 0 7 10 hours ago
Last Post: MikePhua
  Rewiring and Restoring the Kubota KH-191 Excavator’s Electrical System MikePhua 0 6 10 hours ago
Last Post: MikePhua
  Diagnosing Fuel Pressure Drop and Power Loss on a CAT 977L Track Loader MikePhua 0 5 11 hours ago
Last Post: MikePhua
  Troubleshooting Issues with the CAT 428E Loader MikePhua 0 3 Yesterday, 04:56 PM
Last Post: MikePhua
  Troubleshooting Bosch Rexroth Hydrostatic Transmission in Schaeff 831 Loader MikePhua 0 2 Yesterday, 03:57 PM
Last Post: MikePhua
  Hydraulic Filter Service Procedure for the Caterpillar 966B Loader MikePhua 0 1 Yesterday, 03:49 PM
Last Post: MikePhua
  Kubota SVL95-2S Dash Failure and Hour Meter Loss Linked to Gauge Cluster Malfunction MikePhua 0 4 Yesterday, 03:44 PM
Last Post: MikePhua
  Austin-Western Loader Built from Grader Frame Sparks Restoration Interest MikePhua 0 8 Yesterday, 03:41 PM
Last Post: MikePhua
  Understanding the Hydraulic Breather Issues in the Case 580SE MikePhua 0 4 Yesterday, 03:40 PM
Last Post: MikePhua
  Electrical Faults on a 1999 Komatsu WB150 Backhoe Loader and Fuse Blowout Diagnosis MikePhua 0 3 Yesterday, 03:36 PM
Last Post: MikePhua
  Diagnosing Tilt Actuator Malfunction on a Bobcat 864 Loader MikePhua 0 3 Yesterday, 03:35 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)