Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Diagnosing Steering Lock-Up on the Terex 3172-31B Loader
#1
The Terex 3172-31B and Its Hydraulic Steering System
The Terex 3172-31B is a mid-sized wheel loader built for rugged earthmoving and material handling. Like many loaders of its class, it uses a hydraulic orbitrol steering system—also known as a steering control unit (SCU)—mounted at the base of the steering column. This system converts mechanical input from the steering wheel into hydraulic flow, directing fluid to the steering cylinders and enabling smooth articulation.
When functioning properly, the orbitrol allows proportional control in both directions. However, when internal components wear or bind, steering can become erratic, unpredictable, or even dangerous.
Symptoms of Steering Lock-Up
Operators have reported a specific failure mode:
  • Turning the steering wheel quickly causes it to lock solid
  • Reversing the steering direction with force temporarily frees the system
  • Slow, deliberate steering works normally in both directions
  • The issue occurs symmetrically—both left and right turns are affected
This behavior suggests a mechanical or hydraulic restriction inside the orbitrol unit, rather than external cylinder binding or linkage interference.
Understanding Orbitrol Steering Units
Orbitrols are rotary valve assemblies that meter hydraulic flow based on steering input. Inside the unit:
  • A spool and sleeve rotate with the steering wheel
  • Internal springs and centering pins maintain neutral position
  • Check valves and pressure reliefs regulate flow and protect against overload
  • Seals and bushings guide movement and prevent leakage
When the spool binds or the centering mechanism fails, the unit may lock mid-turn or resist rapid input. This is especially common in older machines where fluid contamination or wear has degraded internal tolerances.
Likely Causes of Steering Lock-Up
Based on the symptoms, the most probable causes include:
  • Worn or scored spool and sleeve surfaces
  • Broken centering springs or pins
  • Internal debris from pump or hose degradation
  • Fluid contamination causing sticky movement
  • Pressure imbalance due to faulty check valves
Because the steering works when turned slowly, mechanical interference is unlikely. Instead, the orbitrol may be experiencing hydraulic lag or internal friction that worsens with speed.
Inspection and Repair Strategy
To diagnose and repair:
  • Remove the orbitrol unit from the steering column
  • Disassemble carefully, noting spring orientation and spool alignment
  • Inspect spool and sleeve for scoring, galling, or wear
  • Check centering springs and pins for breakage or distortion
  • Clean all components with lint-free cloth and hydraulic-safe solvent
  • Replace seals, springs, and worn parts using a rebuild kit if available
  • Reassemble with proper torque and alignment
If the orbitrol is beyond repair, replacement may be necessary. OEM units can be expensive, but remanufactured or cross-compatible orbitrols from brands like Eaton or Char-Lynn may offer cost-effective alternatives.
Preventive Measures and Fluid Health
To prevent future steering issues:
  • Change hydraulic fluid at recommended intervals
  • Use fluid with proper anti-wear and anti-foaming additives
  • Install inline filters to catch debris before it reaches the orbitrol
  • Inspect hoses for internal delamination or shedding
  • Avoid overloading the steering system with excessive articulation under load
One operator shared that after rebuilding his orbitrol and flushing the system, steering returned to normal—and the loader felt “like new” during tight maneuvers.
Conclusion
Steering lock-up on the Terex 3172-31B is most likely caused by internal orbitrol wear or contamination. While the issue may seem severe, it’s often repairable with careful disassembly and inspection. By understanding the mechanics of hydraulic steering and maintaining fluid health, operators can restore precise control and extend the life of their loader’s steering system. In machines built to move mountains, steering shouldn’t be a fight—it should be a fingertip command.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Error 8000 on O&K L15.5 Loader and Wheel Pump Diagnostics MikePhua 0 6 3 hours ago
Last Post: MikePhua
  Diagnosing Park Brake Release Issues on the Caterpillar D6H Dozer MikePhua 0 8 8 hours ago
Last Post: MikePhua
  Freeing Stuck Brake Shoes on a Terex TS14 Scraper MikePhua 0 5 8 hours ago
Last Post: MikePhua
  Diagnosing Overheating in the Komatsu PC60-7 Excavator MikePhua 0 7 8 hours ago
Last Post: MikePhua
  Safely Removing the Belly Pan on a CAT 963C Track Loader MikePhua 0 7 8 hours ago
Last Post: MikePhua
  Diagnosing No-Start Issues on a JLG 330CRT After Alternator Replacement MikePhua 0 2 8 hours ago
Last Post: MikePhua
  Diagnosing Slow Bucket Dump on Komatsu PC250LC-6LE MikePhua 0 3 9 hours ago
Last Post: MikePhua
  Diagnosing Fuel Pressure Drop and Power Loss on a CAT 977L Track Loader MikePhua 0 5 9 hours ago
Last Post: MikePhua
  Diagnosing Intermittent Drive Loss on a John Deere 850C Dozer MikePhua 0 3 9 hours ago
Last Post: MikePhua
  Diagnosing Track Lockup on a CAT D5K2 Dozer MikePhua 0 2 9 hours ago
Last Post: MikePhua
  Diagnosing HVAC Display Errors on Komatsu WA380-6 Loaders MikePhua 0 1 9 hours ago
Last Post: MikePhua
  Troubleshooting a Frozen Steering System on Gradall JLG G943A MikePhua 0 3 10 hours ago
Last Post: MikePhua
  Diagnosing Steering Loss on a John Deere 450C MikePhua 0 1 10 hours ago
Last Post: MikePhua
  Diagnosing SCR Heater Failures on Bobcat T770 MikePhua 0 4 10 hours ago
Last Post: MikePhua
  Troubleshooting Issues with the CAT 428E Loader MikePhua 0 3 10 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)