Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Unusual Starting Behavior in the CAT D6N Dozer
#1
Overview of the CAT D6N
The Caterpillar D6N is a mid-size track-type tractor introduced in the early 2000s as part of Caterpillar’s next-generation dozer lineup. Built for versatility, the D6N was designed to bridge the gap between finish grading and heavy pushing. It features a 6.6L CAT C6.6 ACERT engine producing around 150–165 net horsepower depending on configuration, paired with a hydrostatic transmission and advanced load-sensing hydraulics. Caterpillar, founded in 1925, has sold tens of thousands of D6-series dozers globally, with the D6N becoming a staple in roadbuilding, land clearing, and site prep. The model ALY01509 referenced here is a 2005 unit, part of the early production run before Tier 4 emissions upgrades.
Symptoms of Strange Starting Behavior
Operators have reported that after prolonged storage—typically over a month—the D6N exhibits hard starting. The engine cranks for 20–30 seconds, emits heavy fuel smoke, and stumbles before finally firing. Once running, the machine performs normally with no visible smoke or power loss. In one case, the oil level was found to be significantly overfilled, raising concerns about fuel dilution or water ingress.
Terminology Clarification
  • HEUI Injector (Hydraulically Actuated Electronically Controlled Unit Injector): A fuel injector system that uses engine oil pressure to actuate injection, controlled by solenoids and ECM signals.
  • Hydro-lock: A condition where liquid (fuel or coolant) enters the combustion chamber, preventing piston movement and potentially causing engine damage.
  • Transfer Pump: A low-pressure pump that supplies fuel to the HEUI system; internal seal failure can allow fuel to leak into the oil system.
  • Crank Time: Duration the starter motor must turn the engine before ignition occurs.
Possible Causes of Hard Starting
Several mechanical and environmental factors may contribute to the D6N’s unusual startup behavior:
  • Injector Drip: If a HEUI injector fails to seat properly, fuel may leak into the cylinder during shutdown. This can cause a rich mixture and delayed ignition on startup.
  • Transfer Pump Seal Leak: Though rare, a failed seal can allow fuel to migrate into the engine oil, diluting viscosity and affecting injector performance.
  • Battery Drain or Low Voltage: Extended storage with the battery disconnect switch left on can lead to low cranking voltage, slowing starter speed and affecting ECM timing.
  • Water Ingress via Exhaust: The D6N’s under-hood exhaust stack design can allow rainwater to enter the engine if left uncovered, especially during long idle periods.
Field Case Study and Resolution
In one instance, a D6N sat idle for over two months during a rainy spring. Upon startup, the engine cranked sluggishly and emitted dense fuel smoke. The oil level was found to be more than half a gallon over spec. An oil sample revealed excessive water content but tested negative for glycol, ruling out coolant intrusion. The operator traced the issue to rainwater entering through the exhaust stack, which had been left uncovered. After draining the contaminated oil, replacing the filter, and covering the exhaust with a bucket during future storage, the problem did not recur.
Preventive Measures and Recommendations
To avoid similar starting issues in the D6N:
  • Always cover the exhaust stack during extended storage, especially in wet climates.
  • Use a battery disconnect switch and verify voltage before startup.
  • Monitor oil levels before and after long idle periods; investigate any unexplained increases.
  • Periodically sample engine oil for fuel or water contamination.
  • Inspect HEUI injectors for proper seating and replace any showing signs of leakage.
  • Consider installing a rain cap or exhaust flap to prevent water ingress.
Design Implications and Broader Lessons
The D6N’s HEUI system is sensitive to oil quality and pressure. Any contamination—whether from fuel, water, or degraded oil—can affect injector timing and spray pattern. Unlike mechanical injectors, HEUI units rely on precise hydraulic actuation, making them vulnerable to viscosity changes. Additionally, the exhaust routing under the hood, while compact, creates a direct path for water entry if not protected.
In 2010, Caterpillar revised the exhaust design in later D6 models to include better shielding and optional rain caps. However, older units like the 2005 D6N remain susceptible without aftermarket modifications.
Conclusion
Strange starting behavior in the CAT D6N is often a symptom of deeper issues related to injector sealing, fuel contamination, or environmental exposure. By understanding the interaction between HEUI injectors, oil quality, and exhaust design, operators can take proactive steps to prevent hard starts and protect engine integrity. With proper maintenance and storage practices, the D6N continues to be a reliable and productive machine across a wide range of applications.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Removing a Link from a Track Chain on a Case 450 Dozer MikePhua 0 6 5 hours ago
Last Post: MikePhua
  International TD-20B Dozer and DT-429 Engine Push Rod Replacement MikePhua 0 11 Yesterday, 04:18 PM
Last Post: MikePhua
  Cold Weather Starting Problems in the John Deere 270 Skid Steer MikePhua 0 11 Yesterday, 03:12 PM
Last Post: MikePhua
  Rebuilding a Komatsu D155AX-6 Dozer with the Right Technical Resources MikePhua 0 9 Yesterday, 02:58 PM
Last Post: MikePhua
  John Deere 850J Dozer Code TCU620.4 and Electrical Fault Tracing MikePhua 0 10 Yesterday, 02:38 PM
Last Post: MikePhua
  Case 621 Transmission Behavior and Troubleshooting Strategy MikePhua 0 9 Yesterday, 02:36 PM
Last Post: MikePhua
  Diagnosing Brake Failure on the Komatsu D65E-7 Dozer MikePhua 0 10 Yesterday, 02:33 PM
Last Post: MikePhua
  What Happens When a Case Dozer Final Drive Fails MikePhua 0 9 Yesterday, 02:01 PM
Last Post: MikePhua
  Troubleshooting Starting Problems in Genie Lifts MikePhua 0 5 Yesterday, 01:54 PM
Last Post: MikePhua
  Why Does the Blade Drop on a Komatsu D475A-3 Dozer MikePhua 0 10 10-18-2025, 05:50 PM
Last Post: MikePhua
  Addressing Transmission Issues in the 1991 Dresser TD-8 Dozer MikePhua 0 6 10-18-2025, 05:47 PM
Last Post: MikePhua
  Removing the Transmission from a Caterpillar D8K Dozer MikePhua 0 8 10-18-2025, 05:21 PM
Last Post: MikePhua
  Komatsu D85 E8 Dozer Steering Problems: Diagnosis and Solutions MikePhua 0 10 10-18-2025, 05:19 PM
Last Post: MikePhua
  Troubleshooting Low Engine RPM in Komatsu D155A-6 Dozer MikePhua 0 7 10-18-2025, 02:40 PM
Last Post: MikePhua
  Restoring a Fire-Damaged D8K Dozer Without a Cab MikePhua 0 7 10-18-2025, 01:54 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)