Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
How to Change the Control Pattern on a Case 170B Excavator
#1
The Case 170B and Its Mechanical Simplicity
The Case 170B excavator was part of Case’s early hydraulic excavator lineup, built during a time when mechanical reliability and straightforward hydraulics were prioritized over electronic complexity. With an operating weight in the 17–18 ton range and powered by a turbocharged diesel engine, the 170B was designed for general excavation, trenching, and site prep. Its control system is fully hydraulic, with pilot-operated joysticks and valve banks rather than electronic actuators.
Unlike modern excavators that offer pattern change via a selector switch or software toggle, older machines like the 170B require manual reconfiguration of hydraulic lines to change the control pattern.
Terminology Clarification
  • Control Pattern: The layout of joystick movements that control boom, stick, bucket, and swing functions. Common patterns include SAE (backhoe) and ISO (excavator).
  • Pilot Controls: Low-pressure hydraulic signals from the joysticks that actuate the main control valves.
  • Valve Bank: A series of hydraulic valves that direct fluid to the cylinders based on pilot input.
  • Stick and Boom: The two main arms of the excavator; the boom lifts vertically, while the stick extends outward.
Preparation Before Reconfiguration
Before changing the control pattern, it’s critical to immobilize the boom and stick to prevent unintended movement when hydraulic lines are disconnected. This can be done by:
  • Lowering the boom fully and raising the stick slightly
  • Placing cribbing blocks under both arms to support their weight
  • Relieving hydraulic pressure by cycling the controls with the engine off
Labeling the hoses is essential. Use tape and a marker to identify:
  • Boom Up
  • Boom Down
  • Stick In
  • Stick Out
This ensures accurate reconnection and avoids confusion during testing.
Swapping Hydraulic Lines to Change Pattern
The control pattern is determined by how the pilot hoses are routed to the valve bank. To switch from one pattern to another:
  • Disconnect the pilot hoses for Boom Up and Stick Out
  • Swap their positions and reconnect
  • Repeat for Boom Down and Stick In
This reverses the joystick inputs, effectively changing the control pattern. Retighten fittings to 70% torque initially, allowing for adjustments during testing.
Once the hoses are in place:
  • Start the machine and test each function slowly
  • Confirm that joystick movements match the desired pattern
  • If correct, perform final tightening of all fittings
  • Replace any hose clamps or routing brackets that were removed
Field Wisdom and Practical Tips
Operators who’ve worked on older machines often develop their own methods. In Tacoma, one operator converted his Deere backhoe to CAT pattern by rerouting hoses at a single control box. He emphasized the importance of blocking the boom and stick, noting that oil discharge during hose removal can cause sudden movement if not secured.
In rural Virginia, a farmer traced his pilot hoses manually due to lack of documentation. He used colored zip ties to mark each line and took photos before disassembly—a simple but effective strategy.
Recommendations for Safe and Effective Conversion
  • Always depressurize the system before disconnecting any hydraulic lines
  • Use clean rags and caps to prevent contamination during hose swaps
  • Keep a diagram or photo record of original hose routing
  • Test slowly and be prepared to shut down immediately if movement is erratic
  • Consider installing quick-connect fittings if frequent pattern changes are needed
Conclusion
Changing the control pattern on a Case 170B excavator is a hands-on process that requires mechanical awareness and attention to hydraulic safety. While newer machines offer electronic toggles, older models demand manual hose swaps and careful testing. With proper preparation and methodical execution, operators can customize their control layout to match personal preference or crew standard—bringing modern flexibility to a classic machine.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Exploring the Case 1155E Wheel Loader MikePhua 0 4 22 minutes ago
Last Post: MikePhua
  Which Mini Excavator Offers the Best Value Today MikePhua 0 8 37 minutes ago
Last Post: MikePhua
  Case 580B in 1972 A Milestone in Backhoe Evolution MikePhua 0 4 1 hour ago
Last Post: MikePhua
  Choosing the Right Mini Excavator: Key Considerations MikePhua 0 10 2 hours ago
Last Post: MikePhua
  Can You Convert a Takeuchi TL130 from H-Pattern to ISO Controls MikePhua 0 12 3 hours ago
Last Post: MikePhua
  Evaluating the Hitachi EX50U Hydraulic Excavator for Resale MikePhua 0 13 3 hours ago
Last Post: MikePhua
  Mustang 170Z Mini Excavator with Hydraulic Breaker: Performance, Maintenance, and Best Practices MikePhua 0 12 4 hours ago
Last Post: MikePhua
  1988 Case 1845 Skid Steer: Features, Common Issues, and Troubleshooting MikePhua 0 12 4 hours ago
Last Post: MikePhua
  Battery Wiring and Cold Start Configuration on the CAT 325BL Excavator MikePhua 0 12 4 hours ago
Last Post: MikePhua
  Is There a Case Tractor Equivalent to the Ford 545D MikePhua 0 12 4 hours ago
Last Post: MikePhua
  Choosing the Right 5-Ton Mini Excavator MikePhua 0 15 4 hours ago
Last Post: MikePhua
  Mitsubishi MX-35 Excavator: A Compact Yet Powerful Machine for Demanding Tasks MikePhua 0 12 4 hours ago
Last Post: MikePhua
  Understanding the 1994 Case 580 SK Tractor Loader MikePhua 0 13 5 hours ago
Last Post: MikePhua
  Case CX210: An Overview of Performance and Common Issues MikePhua 0 15 5 hours ago
Last Post: MikePhua
  Locating and Interpreting the Fuse Layout for the Case 435 Series 3 Skid Steer MikePhua 0 14 5 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)