Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Komatsu PC200 LC-5 Excavator Hydraulic Cylinder Failure
#1
Machine Overview
The Komatsu PC200 LC-5 is a popular mid-size hydraulic excavator widely used in construction, excavation, and earthmoving projects. It features a powerful Komatsu turbocharged diesel engine producing about 143 horsepower and a sophisticated hydraulic system designed for productivity and fuel efficiency. Built for rugged jobsite conditions, the PC200 LC-5 is recognized for its durability and ease of maintenance.
Hydraulic Cylinder Function
The hydraulic cylinders are critical components that extend and retract to move the excavator’s boom, arm, and bucket. They rely on pressurized hydraulic fluid delivered by pumps and controlled through spool valves and joysticks operated by the user.
Failure Symptoms and Diagnosis
In this case, the hydraulic cylinder was initially stuck in the retracted position when the machine was off. It then slowly drifted out, indicating a leak or loss of hydraulic holding pressure. After restarting the engine, the cylinder snapped back quickly but then locked in a mid-position without any hydraulic response or noise, and no pressure was detected at the control valve.
This type of failure strongly suggests:
  • Internal or external leakage in the hydraulic cylinder causing loss of fluid pressure
  • Possible blockage, contamination, or mechanical failure in the control spool valve preventing pressure from reaching the cylinder
  • Faulty hydraulic hoses or connections disrupting fluid flow
  • Air trapped in hydraulic lines causing erratic cylinder behavior
  • Sensor or control system failure affecting joystick hydraulic valve operation
Troubleshooting Recommendations
  • Visual inspection: Look for external leaks, damaged hoses, or fittings on the cylinder and valve block.
  • Pressure testing: Attach hydraulic gauges to test pressure at the pump output, control valve input, and cylinder ports.
  • Cylinder examination: Remove the cylinder if possible and inspect for seal damage, scoring, or bent rods.
  • Control valve servicing: Clean or replace the spool valve or joystick valve components to ensure fluid flow.
  • Air purging: Bleed air from the hydraulic system carefully to restore consistence.
  • Replace worn or faulty parts identified during inspection to restore function.
Maintenance and Prevention
  • Follow Komatsu’s recommended hydraulic fluid change intervals and use genuine fluids.
  • Regularly inspect hydraulic lines, hoses, and cylinder rods for wear.
  • Avoid operating the machine with known hydraulic irregularities to prevent damage escalation.
  • Keep hydraulic filters clean and replace them per schedule.
  • Train operators to recognize early signs of hydraulic issues such as sluggish or drifting cylinders.
Terminology
  • Spool Valve: Controls direction and flow of hydraulic fluid within the system.
  • Hydraulic Drift: Unintended movement of a cylinder due to fluid leakage or pressure imbalance.
  • Pressure Gauge: Tool to measure hydraulic system pressure to diagnose issues.
  • Bleeding: Removing trapped air from hydraulic fluid lines.
  • Seal: Component preventing fluid leakage in cylinders and valves.
A Practical Story
A PC200 LC-5 operator experienced similar hydraulic cylinder drift after the machine sat idle. Prompt inspection revealed a worn cylinder seal causing fluid bypass. Replacing the seal and conducting a thorough system bleed restored cylinder responsiveness and stability. The operator emphasized the importance of regular inspection after idle periods to detect early leaks that cause such problems.
Conclusion
Hydraulic cylinder failure on the Komatsu PC200 LC-5 shows typical symptoms of pressure loss, valve malfunction, or leakage. Accurate diagnosis involves pressure measurement and component inspection. Preventive maintenance with fluid and seal care plus operator awareness extends hydraulic system life. Timely repairs ensure excavator performance and jobsite productivity remain high.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Dealing with Slow Lift and Overheating Hydraulic Oil in Bobcat 75 XT MikePhua 0 1 1 minute ago
Last Post: MikePhua
  Dealing with Excessive Hydraulic Fluid in Heavy Equipment MikePhua 0 1 5 minutes ago
Last Post: MikePhua
  Takeuchi TB240CRA screen failure and hydraulic claw diagnosis MikePhua 0 3 9 minutes ago
Last Post: MikePhua
  JCB 550-170 Loadall hydraulic failure traced to vibration damper and bevel box coupling MikePhua 0 3 13 minutes ago
Last Post: MikePhua
  Cat TH406C hydraulic overheating traced to transmission clutch slippage and cooling stack contamination MikePhua 0 3 14 minutes ago
Last Post: MikePhua
  Case 580 Super K hazard light fuse failure and electrical diagnosis MikePhua 0 1 18 minutes ago
Last Post: MikePhua
  Case 580K fuel leak at filter head and hydraulic tank seepage MikePhua 0 3 23 minutes ago
Last Post: MikePhua
  Bobcat 721 Hydraulic Problems MikePhua 0 1 25 minutes ago
Last Post: MikePhua
  Volvo L350F exhaust valve spring failure after overhaul MikePhua 0 1 28 minutes ago
Last Post: MikePhua
  Bobcat 753G main belt tension failure and repair strategies MikePhua 0 1 36 minutes ago
Last Post: MikePhua
  JCB 814 Super slew brake solenoid failure and retrofit options MikePhua 0 1 37 minutes ago
Last Post: MikePhua
  Case W36 Hydraulic Issues and Troubleshooting MikePhua 0 1 53 minutes ago
Last Post: MikePhua
  JD319D hydraulic system fails to engage MikePhua 0 1 55 minutes ago
Last Post: MikePhua
  Reviving the John Deere 992ELC Excavator: A Comprehensive Guide MikePhua 0 10 Yesterday, 03:14 PM
Last Post: MikePhua
  Komatsu D37 Track Tension Loss and Adjuster Cylinder Repair MikePhua 0 10 Yesterday, 03:13 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: