Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Removing the Driveline from a Fuller Transmission
#1
Overview
Removing the driveline from a Fuller transmission—a common component in heavy-duty trucks—requires careful disassembly and attention to detail due to the complexity of mechanical parts involved. Fuller transmissions, such as those made by Eaton, are known for their durability and use in applications requiring multiple gear speeds.
Preparation and Safety
  • Begin by securing the vehicle and ensuring it is safely supported to access the transmission system.
  • Place the transmission in neutral and lift the drive wheels off the ground as necessary to avoid drivetrain tension.
  • Drain the transmission lubricant to prevent spills during disassembly.
  • Remove any parking brakes or additional components linked to the driveline.
Tools and Work Environment
  • Use soft-faced hammers, soft bars, and mauls to avoid damage to precision components.
  • Snap ring pliers are essential for handling retaining rings safely.
  • Ensure a clean workspace free from contamination, as dirt and debris can damage bearings or bushings.
  • Bearing pullers and other specialty tools facilitate removal of press-fitted parts without damage.
Disassembly Procedure Highlights
  • Remove the companion flanges from the universal joints connected to the driveline.
  • Detach the retaining capscrews on the bearing housing but avoid removing the housing if not necessary.
  • Using controlled force, drive the gears and shafts forward or backward as specified to free them from their bores.
  • Remove snap rings, washers, keys, and bearings sequentially; keep parts organized to ease reassembly.
  • Inspect bearing condition carefully; clean and re-lubricate if reused, or replace if damaged.
  • Particular attention is required when removing the mainshaft assembly to avoid harming sliding clutch gears and pilot bearings.
Common Challenges and Tips
  • Some components may be firmly seated due to wear or corrosion; apply gradual and even force rather than abrupt impacts.
  • Use of lubrication and appropriate heat can ease parts removal but must be done cautiously to avoid damage.
  • Always verify the orientation and placement of keys and washers during removal for proper reinstallation.
Reassembly Considerations
  • Prior to reinstallation, inspect all components for wear or damage.
  • Replace any questionable parts to prevent early failure.
  • Follow manufacturer torque specifications for all fasteners.
  • Ensure all snaps rings and seals are correctly seated to maintain integrity and prevent leaks.
Terminology Explained
  • Drive Shaft: Rotating component transmitting torque from the transmission to the drive axles.
  • Universal Joint: Flexible joint allowing the driveline to accommodate angular misalignment.
  • Snap Ring: Circular retaining ring used to hold components in position on shafts or in bores.
  • Mainshaft: The primary output shaft within the transmission carrying power to the driveline.
  • Sliding Clutch Gear: Gear that moves axially to engage or disengage gears on shafts.
Conclusion
Removing the driveline from a Fuller transmission demands methodical procedures, proper tools, and clean work conditions to prevent damage and ensure successful disassembly. Understanding component functions and maintenance practices not only extends transmission life but also fosters proficient repairs. This knowledge is vital in heavy-duty vehicle maintenance for mechanics aiming to optimize driveline and transmission reliability.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Safely Removing the Belly Pan on a CAT 963C Track Loader MikePhua 0 7 3 hours ago
Last Post: MikePhua
  Removing a Seized Blade Center Pin from a TD20G Dozer MikePhua 0 5 3 hours ago
Last Post: MikePhua
  Removing a Damaged Lower Kingpin and Rebuilding a Tractor Front Axle MikePhua 0 4 3 hours ago
Last Post: MikePhua
  Troubleshooting Gear Loss in the CAT 143H Motor Grader Transmission MikePhua 0 2 4 hours ago
Last Post: MikePhua
  Is a Case 680 with a Bad Transmission Worth Fixing MikePhua 0 1 4 hours ago
Last Post: MikePhua
  Troubleshooting Low Charge Pressure and Transmission Overheating on the 2006 Case 850K Series 2 MikePhua 0 2 4 hours ago
Last Post: MikePhua
  Removing the Final Drive Pinion on a Caterpillar D3B MikePhua 0 8 4 hours ago
Last Post: MikePhua
  Troubleshooting the 12-H Transmission Light Issue MikePhua 0 2 4 hours ago
Last Post: MikePhua
  Solving Transmission Pressure Loss in the Komatsu WB140-2N MikePhua 0 1 5 hours ago
Last Post: MikePhua
  Diagnosing Gear Loss in the Case 580K Four-Speed Transmission MikePhua 0 4 5 hours ago
Last Post: MikePhua
  Troubleshooting Bosch Rexroth Hydrostatic Transmission in Schaeff 831 Loader MikePhua 0 2 6 hours ago
Last Post: MikePhua
  Replacing Transmission Input and Output Seals on a John Deere 762B Scraper MikePhua 0 1 6 hours ago
Last Post: MikePhua
  Can Shuttle Transmission Failure on a Ford 555 Be Caused by Pickup Screen Blockage MikePhua 0 5 6 hours ago
Last Post: MikePhua
  Transmission Issues in Heavy Equipment: Troubleshooting and Solutions MikePhua 0 6 7 hours ago
Last Post: MikePhua
  Case 821 Loader Transmission Contamination and Solenoid Failure MikePhua 0 5 7 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)