4 hours ago
The ASV PT-60 with its hydrostatic transmission system is a versatile machine widely used in construction and landscaping. However, operators sometimes encounter a frustrating transmission delay issue, particularly a time lag when shifting between forward and reverse, as well as delayed turning motions at a standstill. Understanding the root causes, mechanical and hydraulic principles, and diagnostic procedures is key to maintaining smooth operation and minimizing downtime. This article offers a comprehensive exploration of the ASV PT-60 transmission delay, enriched with technical explanations, practical recommendations, and real-world insights.
Understanding the Hydrostatic Transmission in ASV PT-60
This comprehensive approach ensures the ASV PT-60 continues to meet the demanding needs of various job sites with reliable, efficient performance.
Understanding the Hydrostatic Transmission in ASV PT-60
- The ASV PT-60 utilizes a hydrostatic transmission system where engine power is converted to hydraulic flow which drives hydraulic motors connected to the tracks.
- The system features a charge pressure circuit to maintain hydraulic oil flow and pressure, critical for responsive motion control.
- Travel control involves pilot pressure signals guiding a pilot generation block which manages fluid distribution to drive motors.
- It includes a two-speed range (high and low) nominally on the same drive motor, offering flexibility in speed and power demands.
- Noticeable lag or delay when transitioning from forward to reverse or vice versa.
- Longer delay when attempting to initiate turning motions from a complete stop.
- Reduced responsiveness more pronounced in low range compared to high range speeds.
- Delay is consistent even when the machine is fully warmed up but is slightly less in high range.
- Occasional machine stalling or loss of steering function under load conditions.
- Pilot Generation Block Adjustment:
The pilot generation block and associated valves govern hydraulic pilot pressure. If bias or improper adjustment exists (e.g., favored flow in one direction), delay in control response can occur. Adjusting this block to ensure balanced pilot pressure may improve responsiveness.
- Low Pilot Pressure:
Low pilot pressure reduces hydraulic circuit responsiveness, causing delayed travel and turning. Typical charge pressure should be near 400 psi; dropping significantly (e.g., to 300 psi or lower) indicates pump or system issues.
- Hydraulic Pump Wear or Fault:
Pump wear results in pressure drops under load, especially in low range, leading to sluggish movement or stalling. Evidence includes fluctuating charge pressure and erratic machine response in all directions.
- Control Valve or Solenoid Malfunction:
Faulty valves or solenoids in the hydraulic system can cause delays or erratic control of travel flow.
- Drive Motor Condition:
Usually less likely if pressure issues affect all directions, but worn or damaged motors can cause poor and delayed turning or travel.
- Hydraulic Fluid Quality and Levels:
Low or contaminated hydraulic fluid can cause loss of pressure and slow response.
- Electrical or Safety Switches:
Faulty seat or lap bar switches can interfere with transmission control.
- Check and adjust the pilot generation block for bias and correct pilot pressure balance.
- Measure charge pressure using hydraulic gauges; verify it remains steady near 400 psi during operation.
- Inspect and, if needed, rebuild or replace the hydraulic pump's seal kit, especially if pump wear is suspected.
- Clean or replace hydraulic filters to ensure clean fluid flow.
- Test and verify operation of all control valves and solenoids; replace faulty units.
- Check electrical systems and seat/lap bar switches for consistent signals.
- Confirm hydraulic fluid level and quality; drain and replace fluid if contaminated.
- Regularly service and inspect hydraulic lines and fittings for leaks or restrictions.
- Consider utilizing diagnostic tools specific to Bosch Rexroth systems used in ASV for advanced fault detection.
- A 2008 ASV PT-60 experienced low charge pressures dropping to 300 psi in low range and near zero under load, causing erratic movement and loss of loader functions. The resolved strategy involved running in high range to maintain 400 psi temporarily while planning pump repairs.
- Operators reported replacing costly relieve valves, joysticks, and solenoids without solving drive delays, underscoring the importance of pump condition and pilot system adjustments.
- Field technicians recommend carefully verifying pilot generation block settings and pump health before expensive component replacements.
- When operating under heavy load or on hills, consider switching to high-range speed to reduce transmission stress.
- Maintain a detailed maintenance log of hydraulic system service and observed symptoms to assist troubleshooting.
- Train operators on early signs of transmission delay and the importance of regular hydraulic system checks.
- Plan preventive rebuilds of high-wear components such as pumps every few thousand hours.
- Use manufacturer-approved hydraulic fluids and replacement components to ensure system compatibility and longevity.
- Hydrostatic Transmission: A hydraulic system that uses pressurized fluid to transmit engine power smoothly to drive components without mechanical gears.
- Pilot Pressure: A low-pressure hydraulic signal used to control valves and actuators within the transmission system.
- Pilot Generation Block: A hydraulic valve assembly that produces and controls pilot pressure for directional and speed commands.
- Charge Pressure: Constant hydraulic pressure within the system to maintain fluid flow and compensate for leaks or load.
- Seal Kit (Hydraulic Pump): Set of seals and gaskets used to refurbish the hydraulic pump to maintain pressure and prevent leaks.
- Solenoid: An electromechanical valve actuator controlling fluid flow in response to electrical signals.
- Lap Bar Switch: Safety switch that detects operator presence and enables or disables machine functions accordingly.
This comprehensive approach ensures the ASV PT-60 continues to meet the demanding needs of various job sites with reliable, efficient performance.
