Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Oil Discharge from Valve Cover Vent on Yanmar 2TN66L-UTBA: Diagnosing Crankcase Ventilation and Seasonal Effects
#1
Introduction to the Issue
The Yanmar 2TN66L-UTBA engine, commonly found in compact excavators like the Takeuchi TB007, is a small two-cylinder diesel powerplant known for its reliability in tight applications. However, when oil begins dripping from the crankcase breather tube—especially after winter storage—it raises questions about internal pressure, oil level, and system integrity. In one case, oil was observed dripping onto the track shortly after startup, traced to the valve cover vent tube. The incident prompted a deeper look into possible causes and preventive strategies.
Terminology Explained
- Crankcase Ventilation Tube: A pipe that allows pressure and vapors to escape from the engine’s crankcase, often routed downward to prevent contamination
- Road Draft Tube: An older term for passive crankcase vents that rely on vehicle motion to create suction
- Blowby: Combustion gases leaking past piston rings into the crankcase, increasing internal pressure
- Oil Aeration: The mixing of air with oil, which can cause frothing and pressure spikes
Possible Causes of Oil Discharge
1. Overfilled Crankcase
  • A well-meaning operator added a quart of oil without checking the dipstick, leading to overfilling. Excess oil can be forced out through the breather tube, especially during cold starts when oil is thick and pressure spikes.
2. Cold Oil Behavior
  • Thick oil during cold starts may not circulate quickly, causing temporary pooling in the valve cover. If drain-back holes are restricted or slow, oil may be pushed out the vent.
3. Blocked or Restricted Drain Holes
  • Upon inspection, the valve cover lacked obvious drain-back holes. If sludge or varnish buildup restricts oil return to the sump, oil may accumulate and exit through the vent.
4. Fuel Dilution (Ruled Out)
  • In similar cases, diesel fuel leaking into the crankcase via a failed injector pump seal can thin the oil and raise the level. However, in this instance, the oil showed no signs of thinning or fuel contamination.
Field Anecdote: The Garden Tractor Parallel
One operator recalled seeing similar symptoms in garden tractors where carburetor needle valves failed, allowing fuel to flood the crankcase. While not applicable to diesel engines, the principle of fluid migration causing overfill remains relevant.
Recommended Diagnostic and Preventive Steps
  • Check oil level before startup, especially after long storage
  • Use synthetic oil (e.g., 5W-40 Turbo Diesel) to improve cold flow and reduce pressure spikes
  • Inspect breather tube for obstructions or damage
  • Clean valve cover and inspect for sludge or blocked drain passages
  • Monitor for recurring symptoms and consider compression testing to rule out excessive blowby
Technical Parameters and Suggestions
  • Engine model: Yanmar 2TN66L-UTBA
  • Oil capacity: ~2.5–3.0 liters
  • Recommended oil: 10W-30 or 5W-40 synthetic diesel oil
  • Breather tube location: Top of valve cover, routed downward
  • Typical crankcase pressure: Slightly negative to neutral under normal operation
Preventive Maintenance Tips
  • Change oil annually or every 250 hours
  • Store machine with crankcase vent protected from moisture ingress
  • Run engine monthly during off-season to circulate fluids
  • Use dipstick as primary reference—avoid guessing oil level
  • Replace breather grommet or seal if signs of leakage persist
Conclusion: A Seasonal Symptom, Not a Systemic Failure
Oil discharge from the valve cover vent on the Yanmar 2TN66L-UTBA is often a one-time event triggered by overfilling, cold oil behavior, or temporary pressure imbalance. While alarming at first glance, it rarely indicates serious internal damage. With proper oil management, seasonal startup procedures, and a watchful eye on crankcase ventilation, operators can prevent recurrence and keep these compact engines running smoothly.
As one technician put it, “Sometimes the engine’s just clearing its throat after a long winter nap.”
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Diagnosing hydraulic quick attach failure on the Takeuchi TL230 MikePhua 0 9 4 hours ago
Last Post: MikePhua
  Diagnosing and Fixing Exhaust Popping Sounds on a 48A MikePhua 0 11 Yesterday, 02:33 PM
Last Post: MikePhua
  Diagnosing low power in a 1999 Mack RD688S with E7 VMAC III system MikePhua 0 11 Yesterday, 02:25 PM
Last Post: MikePhua
  Volvo L350F exhaust valve spring failure after overhaul MikePhua 0 6 Yesterday, 02:03 PM
Last Post: MikePhua
  Diagnosing Control Lag in the Simon 32' All-Terrain Scissor Lift MikePhua 0 13 10-19-2025, 03:20 PM
Last Post: MikePhua
  Diagnosing and Resolving Engine Knock in JCB 1550 Backhoes MikePhua 0 7 10-19-2025, 03:06 PM
Last Post: MikePhua
  Bobcat T770 Tilt Circuit Drift and Valve Troubleshooting MikePhua 0 12 10-19-2025, 02:54 PM
Last Post: MikePhua
  Diagnosing and Resolving Crankshaft Position Sensor Issues in Caterpillar 299D MikePhua 0 7 10-19-2025, 02:33 PM
Last Post: MikePhua
  Diagnosing Brake Failure on the Komatsu D65E-7 Dozer MikePhua 0 10 10-19-2025, 02:33 PM
Last Post: MikePhua
  Why Does the Boom Settle on a Yanmar VIO35-6 After Shutdown MikePhua 0 10 10-19-2025, 01:58 PM
Last Post: MikePhua
  How Hard Is It to Add a Third Valve to a CAT 953 or 963 Loader MikePhua 0 12 10-18-2025, 08:18 PM
Last Post: MikePhua
  Replacing the Brakes on a CAT D4D Without Removing the Massive Cover MikePhua 0 9 10-18-2025, 08:08 PM
Last Post: MikePhua
  Diagnosing Starter Failure on the International Harvester 100E MikePhua 0 5 10-18-2025, 08:05 PM
Last Post: MikePhua
  Diagnosing Hydraulic Failure on the CAT 951C Track Loader MikePhua 0 7 10-18-2025, 07:53 PM
Last Post: MikePhua
  Diagnosing Oil Contamination in a Deutz BF4M1012 Engine MikePhua 0 7 10-18-2025, 07:50 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)