Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Diagnosing and Repairing Boom Cylinder Leaks on the Hitachi EX150 Excavator
#1
Understanding the Problem: Hydraulic Cylinder Leakage
Hydraulic cylinder leaks are a common issue in aging excavators, particularly in models like the Hitachi EX150 from the early 1990s. When boom cylinders begin to leak, it’s typically due to worn-out seals, pitted rods, or internal scoring. These leaks not only reduce lifting power but also pose safety risks and increase operating costs through fluid loss and contamination.
In the EX150, the boom cylinders are responsible for lifting the main arm. A leak in these components can manifest as visible oil seepage around the gland, sluggish movement, or hydraulic fluid pooling on the tracks.
Terminology Clarification
- Cylinder Packing: The internal seal assembly that prevents hydraulic fluid from escaping the cylinder.
- Gland Nut: The threaded cap that holds the seal pack in place at the cylinder head.
- Rod: The polished steel shaft that extends and retracts from the cylinder barrel.
- Barrel: The main body of the cylinder that houses the piston and hydraulic fluid.
- Seal Kit: A set of replacement seals, including wipers, O-rings, and backup rings, used to rebuild a hydraulic cylinder.
Disassembly and Removal Techniques
Removing a boom cylinder from an excavator requires careful planning and safe rigging. Here’s a practical method used by field technicians:
  • Use a strong rope or strap looped over the boom to support the cylinder rod.
  • Attach the strap to a stable anchor point such as a tractor hitch, chain block, or overhead beam.
  • Relieve hydraulic pressure by jiggling the joysticks with the engine off, then wait overnight before cracking lines.
  • Loosen the boom pin halfway to allow partial support from the opposite cylinder.
  • Lower the cylinder gently onto wooden planks laid across the tracks or into a nearby truck bed.
  • Drain hydraulic oil slowly by inserting a hose into the port and retracting the rod gradually.
  • Remove bottom pins and slide the cylinder out using leverage and support blocks.
This method minimizes oil spills and avoids sudden drops, especially when working without a crane.
Repair Costs and Labor Estimates
The cost of repairing a leaking boom cylinder varies based on location, labor rates, and parts availability:
  • Genuine seal kits: CAD $900 per cylinder (dealer pricing)
  • Aftermarket seal kits: USD $50–100 per cylinder
  • Labor at hydraulic shop: USD $200–600 per cylinder depending on size and complexity
  • DIY labor: Requires tools like a 48-inch pipe wrench, torque equipment, and a clean workspace
The gland nut on the EX150 cylinders may require thousands of pounds of torque to loosen. Without proper tools, sending the cylinder to a hydraulic shop is recommended.
Choosing Seal Kits: OEM vs Aftermarket
While OEM (Original Equipment Manufacturer) seals are engineered to exact specifications, their cost can be prohibitive. Many reputable hydraulic shops use aftermarket kits from brands like Hercules, which offer:
  • Comparable material quality (e.g., polyurethane, Viton)
  • Pressure ratings up to 5,000 psi
  • Compatibility with Hitachi cylinder dimensions
  • Significant cost savings—often under CAD $300 for both cylinders
In one case, a Canadian farmer sourced aftermarket kits for CAD $287 total, compared to CAD $950 per cylinder from the dealer.
Field Story: Excavator Repair in Rural Alberta
A farmer in Stony Plain, Alberta purchased a used Hitachi EX150 and discovered leaks in both boom cylinders. With limited dealer support and high OEM pricing, he consulted a local hydraulic shop known for servicing oil sands equipment. The shop offered seal replacements at a fraction of the cost and even fabricated custom pins for other components. The repair restored full boom functionality, and the machine returned to service within days.
Preventive Measures and Inspection Tips
To avoid future leaks and extend cylinder life:
  • Inspect rods for pitting or scoring before installing new seals
  • Polish minor imperfections with fine emery cloth
  • Use thread sealant on hydraulic fittings to prevent seepage
  • Cap hydraulic lines during disassembly to prevent contamination
  • Pressure test rebuilt cylinders before reinstallation
  • Avoid overextending the boom during operation, which stresses the seals
Suggested Parameters for the EX150 Boom Cylinder
While exact specs may vary slightly, typical parameters include:
  • Rod diameter: 70–80 mm
  • Barrel diameter: 120–140 mm
  • Stroke length: 1,200–1,500 mm
  • Operating pressure: 3,000–3,500 psi
  • Seal material: NBR or polyurethane with PTFE backup rings
Conclusion: Practical Solutions for Legacy Equipment
The Hitachi EX150 remains a capable excavator despite its age, and boom cylinder leaks are a solvable issue with the right approach. Whether using aftermarket seals, leveraging local hydraulic expertise, or applying DIY ingenuity, operators can restore performance without excessive cost. In the world of heavy equipment, resourcefulness often trumps brand loyalty—and a well-repaired cylinder is proof that even a 30-year-old machine can still earn its keep.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Troubleshooting Jerky Boom Cylinder Movement on CAT 301.6C MikePhua 0 6 2 hours ago
Last Post: MikePhua
  Resolving Hydraulic Fluid Leaks in the Final Drive of a John Deere 70D Excavator MikePhua 0 3 2 hours ago
Last Post: MikePhua
  Hitachi EX50 URG Bottom Rollers: Maintenance and Troubleshooting MikePhua 0 6 2 hours ago
Last Post: MikePhua
  Diagnosing Park Brake Release Issues on the Caterpillar D6H Dozer MikePhua 0 8 2 hours ago
Last Post: MikePhua
  Troubleshooting Fault Code 115 on the Case CX210 Excavator MikePhua 0 8 2 hours ago
Last Post: MikePhua
  Troubleshooting Komatsu Excavator with No Hydraulics MikePhua 0 7 2 hours ago
Last Post: MikePhua
  Resolving ECU Communication Errors on the Volvo ECR145C Excavator MikePhua 0 3 2 hours ago
Last Post: MikePhua
  Diagnosing Overheating in the Komatsu PC60-7 Excavator MikePhua 0 7 2 hours ago
Last Post: MikePhua
  Rewiring and Restoring the Kubota KH-191 Excavator’s Electrical System MikePhua 0 6 2 hours ago
Last Post: MikePhua
  Diagnosing No-Start Issues on a JLG 330CRT After Alternator Replacement MikePhua 0 2 2 hours ago
Last Post: MikePhua
  Troubleshooting Slow Hydraulic Response on Hitachi Zaxis 50U MikePhua 0 5 2 hours ago
Last Post: MikePhua
  Diagnosing Slow Bucket Dump on Komatsu PC250LC-6LE MikePhua 0 3 2 hours ago
Last Post: MikePhua
  Diagnosing Fuel Pressure Drop and Power Loss on a CAT 977L Track Loader MikePhua 0 5 2 hours ago
Last Post: MikePhua
  Replacing Track Idler Bearings on a CAT 304.5 Mini Excavator MikePhua 0 4 3 hours ago
Last Post: MikePhua
  Restoring Throttle Motor Wiring on a Komatsu PC120-5 Excavator MikePhua 0 3 3 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)