Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Troubleshooting Skid Steer Tracking Issues After New Pump Installation
#1
Overview of the Problem
A common issue faced by skid steer operators and mechanics arises when a new hydraulic pump is installed, but the machine no longer tracks straight during operation. This problem affects maneuverability, efficiency, and operator safety, and it can stem from various mechanical or hydraulic faults introduced during or after the pump replacement.
Typical Symptoms
  • Skid steer veers or pulls to one side when moving forward
  • Uneven track or wheel speed during travel
  • Difficulty maintaining a straight line without constant steering input
  • Possible abnormal noises or vibrations
  • Reduced overall machine performance
Possible Causes
  • Pump Mismatch or Incorrect Installation
    Installing a pump with different specifications, flow rates, or pressure characteristics from the original can cause imbalance between the drive circuits.
  • Air Trapped in Hydraulic Lines
    If the hydraulic system wasn’t properly bled after pump replacement, air bubbles can cause inconsistent pressure and erratic track movement.
  • Hydraulic Hose Routing or Damage
    Incorrect hose connections or pinched lines can restrict flow, leading to one side underperforming.
  • Valve or Control Issues
    Steering or differential control valves might need recalibration or could have been disturbed during pump replacement.
  • Mechanical Wear or Damage
    Components such as track drive motors, sprockets, or chains may have pre-existing wear exacerbated by altered hydraulic flow.
  • Improper Pump Settings or Calibration
    Some pumps require precise adjustments or electronic calibrations that, if omitted, cause uneven output.
Diagnostic Steps
  • Verify pump part number and specifications match machine requirements.
  • Inspect all hydraulic hoses for correct routing, connection tightness, and signs of damage.
  • Perform hydraulic system bleeding to remove trapped air.
  • Check steering and drive valve settings for proper adjustment.
  • Observe track or wheel speeds individually during operation to identify disparities.
  • Inspect mechanical components of the drive system for wear or damage.
  • Consult manufacturer service manuals for pump calibration procedures.
Maintenance and Repair Recommendations
  • Always use manufacturer-approved pumps with matching specifications.
  • Follow thorough bleeding procedures post-installation to ensure air-free hydraulics.
  • Routinely inspect and replace worn mechanical parts affecting tracking.
  • Adjust or recalibrate control valves and pump settings according to factory guidelines.
  • Employ professional diagnostic equipment when necessary for pressure and flow measurements.
Case Example
A skid steer operator replaced a worn hydraulic pump with an aftermarket unit that, despite fitting correctly, delivered slightly different flow rates. Post-installation, the machine drifted to the left on every forward pass. After troubleshooting, the mechanic discovered improper bleeding and minor hose kinking on the right side. Correcting hose placement, performing a comprehensive bleed, and fine-tuning valve settings restored straight tracking, illustrating the importance of system-wide checks beyond just component replacement.
Terminology Glossary
  • Tracking: The ability of a skid steer to move straight without pulling to one side.
  • Hydraulic Pump: A device that converts mechanical power into hydraulic energy to drive motors.
  • Bleeding: The process of removing air from hydraulic lines.
  • Control Valve: A valve that directs hydraulic fluid flow to control machine movements.
  • Flow Rate: The volume of hydraulic fluid delivered by the pump over time.
  • Calibration: Adjustment of components to achieve desired operating parameters.
Preventive Measures
  • Source hydraulic components only from reputable suppliers.
  • Document and follow correct installation and bleeding procedures.
  • Train technicians on system diagnostics and calibration.
  • Schedule regular inspections to catch early signs of mechanical or hydraulic wear.
  • Maintain detailed service records for troubleshooting historical issues.
Conclusion
When a skid steer fails to track straight after a new pump installation, the cause often extends beyond the pump itself to system-wide hydraulic and mechanical factors. A methodical approach involving verification of pump compatibility, bleeding of the hydraulic system, hose inspection, valve adjustment, and mechanical checks ensures restoration of proper tracking. Real-world cases demonstrate that thorough diagnostics and adherence to manufacturer protocols safeguard machine performance and operator confidence, reducing downtime and costly repairs.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Troubleshooting Slow Hydraulics in the TMS300 MikePhua 0 1 2 minutes ago
Last Post: MikePhua
  Volvo EC160CL Final Drive: Maintenance and Troubleshooting Insights MikePhua 0 1 3 minutes ago
Last Post: MikePhua
  Caterpillar TH417 Telehandler Troubleshooting and System Recovery MikePhua 0 1 3 minutes ago
Last Post: MikePhua
  Troubleshooting the Case 1450: Addressing a Dead Machine in the Tracks MikePhua 0 1 8 minutes ago
Last Post: MikePhua
  Troubleshooting Injector Problems in Bobcat 863 C Series Skid Steer MikePhua 0 1 12 minutes ago
Last Post: MikePhua
  Troubleshooting Error Code 009 in Heavy Equipment: Causes and Solutions MikePhua 0 1 13 minutes ago
Last Post: MikePhua
  Mustang 2054 Skid Steer Troubleshooting and Reliability Restoration MikePhua 0 1 16 minutes ago
Last Post: MikePhua
  Troubleshooting the E-Pump De-Stroke Issue in the 790E MikePhua 0 1 19 minutes ago
Last Post: MikePhua
  Troubleshooting Rabbit Mode Issues in the 1996 Hitachi EX135USB-5 Excavator MikePhua 0 1 19 minutes ago
Last Post: MikePhua
  Understanding the TMZ50 and 76383 Board Schematics for Troubleshooting MikePhua 0 3 22 minutes ago
Last Post: MikePhua
  Bobcat T595 Bob-Tach Troubleshooting and Electrical System Reliability MikePhua 0 3 24 minutes ago
Last Post: MikePhua
  Troubleshooting the Hitachi EX 120-3 PVC Computer System MikePhua 0 1 41 minutes ago
Last Post: MikePhua
  Coolant Leak Troubleshooting on the Caterpillar IT24 Loader MikePhua 0 2 42 minutes ago
Last Post: MikePhua
  Transmission and Hydraulics Issues in the Gradall 534D-6 Telehandler MikePhua 0 5 44 minutes ago
Last Post: MikePhua
  CAT 320C Injection Pump Diagnostics and Fuel System Reliability MikePhua 0 2 44 minutes ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)