Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Troubleshooting the Early Case 580 CK Shuttle Transmission
#1
I’ve been experiencing some issues with the shuttle transmission on my early model Case 580 CK backhoe, and I wanted to reach out to the community for some insights. This is an older machine, and while it’s served me well over the years, the shuttle has started acting up. I’m hoping to get some advice from those who’ve worked with this model or have experience with similar issues.

Problem Overview
The main issue I’ve been facing is with the shuttle transmission not engaging properly. It’s been slipping when shifting from forward to reverse, and there’s noticeable hesitation when moving in either direction. The machine sometimes has trouble picking up speed or holding a steady gear, especially when under load. It seems to work fine when first starting the engine, but as the machine warms up, the problem worsens.

Possible Causes and Initial Steps
After doing some research, it seems like this issue could be caused by a few things:
  1. Hydraulic Fluid Low or Contaminated: One of the first things I checked was the hydraulic fluid level. If the fluid is low or contaminated, it could affect the performance of the shuttle transmission. I topped it off and cleaned the filter, but the problem persisted.
  2. Worn or Damaged Clutch Pack: Another potential issue could be with the clutch pack inside the transmission. Over time, these parts can wear out and cause slipping or delayed engagement. This might require a more in-depth repair.
  3. Faulty Shuttle Valve: I’ve also read that the shuttle valve can sometimes become clogged or fail, leading to transmission problems. I haven’t been able to access the valve yet, but that might be another area to inspect.
  4. Transmission Linkage Issues: If the linkage is out of alignment or has worn parts, it can cause improper engagement of the gears. This would also require a thorough inspection.

Community Input and Suggestions
Some forum members suggested a few other potential causes that I hadn’t considered:
  • Pressure Test: A couple of users recommended performing a pressure test on the transmission to check if the hydraulic pressure is within the proper range. If the pressure is too low, that could explain the slipping and hesitation.
  • Transmission Adjustment: One user shared that the shuttle lever might need adjustment. If it’s not properly aligned, it can cause issues with gear engagement. I’m planning to adjust this and see if that makes a difference.
  • Fluid Change: A few others pointed out that changing the hydraulic fluid could help, especially if the fluid is old or contaminated. This could potentially clear up some of the slipping issues.

Next Steps for Repair
Based on the advice from the forum and my own observations, I plan to:
  1. Check Fluid Again: Make sure the fluid is clean and at the correct level. If it’s been a while since the last change, I’ll go ahead and replace it.
  2. Inspect the Shuttle Valve: I’ll remove the valve and check for any signs of damage or blockage. Cleaning or replacing it might fix the issue if it’s malfunctioning.
  3. Examine the Clutch Pack: If everything else checks out, I’ll look into the clutch pack and see if it’s worn down. If necessary, I’ll replace the parts.
  4. Perform Pressure Test: If the fluid and components seem fine, I’ll perform a pressure test to see if that’s where the issue lies.

Final Thoughts
The Case 580 CK has been a reliable machine, and I’m hopeful that with some troubleshooting and routine maintenance, I’ll be able to get the shuttle transmission back in working order. I’ll keep the community posted on any progress, and I really appreciate the input I’ve received so far. Hopefully, this will be a relatively simple fix and I can get back to using the machine without too many issues.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Troubleshooting Transmission Problems in the TD8E Dozer MikePhua 0 3 17 minutes ago
Last Post: MikePhua
  JCB Slew Brake Problem: Troubleshooting and Solutions MikePhua 0 2 17 minutes ago
Last Post: MikePhua
  Case 430 Shutting Down: Troubleshooting Common Issues MikePhua 0 3 56 minutes ago
Last Post: MikePhua
  Broken Loader Frame Pivot on Case 580B: Diagnosis and Repair MikePhua 0 4 57 minutes ago
Last Post: MikePhua
  Case 580K No Drive at Rear Wheels: Troubleshooting and Fixes MikePhua 0 3 57 minutes ago
Last Post: MikePhua
  My New Old Hoe: Restoring a Case 580K Backhoe Loader MikePhua 0 3 59 minutes ago
Last Post: MikePhua
  CAT 308E2 Boom Slow to Lower: Troubleshooting and Solutions MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Troubleshooting Hydraulic Pump Issues in CAT 953C MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Case 580 Super M Front Axle Pin Wear: Troubleshooting and Solutions MikePhua 0 3 1 hour ago
Last Post: MikePhua
  Komatsu D20 Help Needed: Troubleshooting and Maintenance Guide MikePhua 0 3 1 hour ago
Last Post: MikePhua
  CAT 962H Poor Hydraulics: Troubleshooting and Solutions MikePhua 0 5 1 hour ago
Last Post: MikePhua
  John Deere 7775 Start and Stall Issue: Troubleshooting and Solutions MikePhua 0 5 1 hour ago
Last Post: MikePhua
  Grease Fittings on the Case 580B: Importance and Maintenance Tips MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Understanding the D4C Hystat: Troubleshooting and Solutions MikePhua 0 8 2 hours ago
Last Post: MikePhua
  CAT 315BL Monitor Issues: Troubleshooting and Solutions MikePhua 0 4 2 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)