Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Owning and Operating a Dynahoe 190-2 Backhoe Loader
#1
The Dynahoe Legacy and Model Overview
Dynahoe was a brand of heavy-duty backhoe loaders originally manufactured by the Warner & Swasey Company, later acquired by Bucyrus-Erie. The Dynahoe 190-2, introduced in the 1970s, was built for industrial-scale excavation and land clearing. Unlike compact backhoes, the 190-2 was a full-sized machine weighing approximately 10 tons, powered by a Detroit Diesel 3-53 engine. Its rugged frame, oversized hydraulic cylinders, and deep digging capability made it popular among municipalities, contractors, and landowners with serious earthmoving needs.
Though production ceased decades ago, Dynahoes remain in use thanks to their overbuilt design and mechanical simplicity. Their cult following among vintage equipment enthusiasts has kept parts circulating through salvage yards, online groups, and private collections.
Terminology Annotation
- Detroit Diesel 3-53: A 3-cylinder, 2-stroke diesel engine known for its durability and distinctive sound.
- Hydraulic Cylinder Repack: The process of replacing internal seals and wear rings to restore pressure and eliminate leaks.
- Starter Solenoid: An electrical relay that engages the starter motor when the ignition key is turned.
- Fuel Canister Filter: A cartridge-style fuel filter used in older diesel systems, often requiring manual priming.
- Hydraulic Snowcone: A humorous term for a large spill of hydraulic fluid, often caused by a burst hose under pressure.
Initial Ownership Experience and Challenges
One new owner acquired two Dynahoe 190-2 machines—one primary unit and one spare. Both were running upon delivery, though the spare had leaky hydraulic pistons. On a cold day, the main machine refused to start, while the spare fired up after coaxing. After a few minutes of smooth operation, the spare stalled with the bucket suspended over a rock wall, requiring creative propping with a log.
Suspecting bad fuel, the owner began troubleshooting. Meanwhile, the main machine was started and tested, only to blow a hydraulic hose while lifting the front end. This resulted in a large fluid spill and two disabled machines in the yard. The experience highlighted the reality of owning vintage equipment: repairs begin sooner than expected.
Fuel System Troubleshooting and Cold Weather Tips
Older diesel machines like the Dynahoe 190-2 are sensitive to fuel quality, especially after long storage. Common issues include:
  • Water contamination in the tank
  • Algae growth in diesel fuel
  • Air intrusion from low tank levels during transport
  • Plugged fuel filters from sediment or microbial buildup
Recommended steps:
  • Drain and inspect fuel filters (both low and high pressure)
  • Check for water in the filter bowls
  • Prime the system manually until fuel overflows at the bleed screw
  • Inspect the fuel tank for rust flakes or debris blocking the feed line
  • Use fuel additives like biocides or anti-gel formulas in cold weather
One operator added an electric fuel pump between the tank and filters to maintain prime and discovered a leaking seal at the back of the gear pump. This kind of diagnosis is common with older Detroits, which can suck air internally under load.
Hydraulic System Maintenance and Hose Replacement
The Dynahoe’s hydraulic system is robust but prone to leaks due to aging hoses and seals. Blown hoses are common when operators push the machine too hard or operate in freezing conditions. Preventive measures include:
  • Replacing hoses with modern hydraulic-rated lines (avoid automotive fuel hose)
  • Repacking cylinders with new seals (requires heavy-duty tools or professional help)
  • Keeping spare hoses and fittings on hand for field repairs
  • Using AW46 hydraulic fluid, available in bulk at retailers like Costco
One owner reported repacking three cylinders and repairing a crack between the bucket arms. Having a second machine proved invaluable for lifting and disassembly during repairs.
Starter Solenoid and Electrical Repairs
Cold weather and rushed repairs led to a snapped starter solenoid while tightening cables. The solenoid was replaced for $35, and the starter reinstalled with only two bolts—though a third was added later for security. These solenoids are often standard parts available at auto parts stores.
Electrical systems on Dynahoes are simple but vulnerable to corrosion and vibration. Recommendations:
  • Clean all terminals and apply dielectric grease
  • Replace cracked wires and brittle insulation
  • Keep spare solenoids and relays in the cab
Parts Availability and Community Support
Service manuals for Dynahoe machines are rare, but parts books and operator manuals are still circulating. Online groups and forums offer diagrams, photos, and advice. Some vendors sell NOS (new old stock) parts, though prices can be high. Filters are readily available through NAPA and similar suppliers.
Having two machines allows owners to swap parts, test components, and perform repairs without downtime. This strategy is especially useful when dealing with large cylinders or hard-to-access components.
Conclusion
Owning a Dynahoe 190-2 is a commitment to mechanical problem-solving and vintage iron stewardship. These machines are powerful, overbuilt, and capable of serious work—but they demand attention, patience, and a willingness to get dirty. From fuel system quirks to hydraulic leaks and starter repairs, the learning curve is steep but rewarding. With community support, spare parts, and a second machine for backup, even a first-time owner can keep a Dynahoe running strong.
Reply


Messages In This Thread
Owning and Operating a Dynahoe 190-2 Backhoe Loader - by MikePhua - 09-04-2025, 02:02 PM

Possibly Related Threads…
Thread Author Replies Views Last Post
  Restoring and Operating a Case 1845C Skid Steer with Confidence MikePhua 0 7 4 hours ago
Last Post: MikePhua
  Choosing the Right Skid Loader for Heavy Mat Handling MikePhua 0 5 9 hours ago
Last Post: MikePhua
  Exploring the Case 1155E Wheel Loader MikePhua 0 4 9 hours ago
Last Post: MikePhua
  The Dangers of Allowing People to Ride in Loader Buckets MikePhua 0 8 9 hours ago
Last Post: MikePhua
  CAT IT28F Wheel Loader Overview MikePhua 0 8 10 hours ago
Last Post: MikePhua
  Case 580B in 1972 A Milestone in Backhoe Evolution MikePhua 0 4 10 hours ago
Last Post: MikePhua
  Operating the Genie Z-45/25 on Sloped Terrain MikePhua 0 9 10 hours ago
Last Post: MikePhua
  Volvo L70E vs L70F Wheel Loaders in Harsh Operating Conditions MikePhua 0 6 11 hours ago
Last Post: MikePhua
  Evaluating the Caterpillar 933 Track Loader for Farm and Utility Use MikePhua 0 9 11 hours ago
Last Post: MikePhua
  Evaluating the Mitsubishi WS200 Wheel Loader for Field Use and Restoration MikePhua 0 7 Yesterday, 03:57 PM
Last Post: MikePhua
  Component Weights and Salvage Insights for the Michigan 475C Wheel Loader MikePhua 0 11 Yesterday, 03:10 PM
Last Post: MikePhua
  Can the MF54A Backhoe Attach to a Massey Ferguson 40 Tractor Without Modification MikePhua 0 10 Yesterday, 02:04 PM
Last Post: MikePhua
  Volvo L180: A Robust Workhorse in the Wheel Loader Category MikePhua 0 13 Yesterday, 01:59 PM
Last Post: MikePhua
  John Deere 510 Backhoe: A Reliable Workhorse in Construction and Excavation MikePhua 0 11 Yesterday, 01:55 PM
Last Post: MikePhua
  Exploring the 2011 CAT 262C Skid Steer Loader MikePhua 0 14 Yesterday, 01:15 PM
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)