Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Komatsu SK818 Troubles and Solutions
#1
Brief Introduction to the Komatsu SK818
The Komatsu SK818-5 is a compact skid-steer loader produced between 2003 and 2012. Engineered for versatility, it's driven by a Komatsu 4D88E diesel engine delivering approximately 34 kW (46.8 hp), and offers an operating capacity of around 870 kg.  Its bucket can handle up to 0.4 cubic meters, reaching a discharge height of roughly 2.28 meters, with travel speed capped at 16 km/h.
Komatsu, the company behind it, is a globally recognized heavy equipment manufacturer founded in Japan in 1921. It holds the position of the second-largest construction machinery maker worldwide.
Common Hydraulic Troubles
Multiple owners report hydraulic responsiveness issues or sluggish loader behavior, especially under load. A key recommendation is to inspect the main hydraulic pressure relief valve for proper seating and corrosion-free operation. Adjusting (increasing) the pilot pressure slightly may restore function.
Beyond that, general hydraulic trouble can stem from:
  • Air leakage at the pump inlet or hoses, affecting pressure delivery.
  • Worn, misaligned, or dirty pump components reducing hydraulic efficiency.
  • Clogged filters or tubing restrictions, hampering fluid flow.
  • Low fluid levels or contaminated oil, impacting system responsiveness.
  • Worn cylinders, valves, or bearings, leading to erratic or slow controls.
Diagnostic Approach
A systematic troubleshooting process is essential:
  1. Clarify the symptom (e.g., sluggish lift arms vs. poor pushing power) to narrow root causes.
  2. Gather operator feedback—noting when issues began, what loads or conditions triggered them.
  3. Check filters, fluid levels, and bleed the system to expel any trapped air.
  4. Inspect for air leaks in suction lines, pump alignment, and ensure couplings and hoses are tight.
Case Story: Pressure Relief Valve Issue
A technician shared an example where a Komatsu loader lost drive power under load. The resolution involved cleaning and reseating the main relief valve, then gently adjusting pilot pressure—restoring normal hydraulic drive.
Maintenance Recommendations
Regular maintenance is key to preserving hydraulic performance:
  • Perform filter replacements and fluid changes at intervals recommended in the service manual.
  • Frequently bleed the system to eliminate air, especially after servicing.
  • Use clean hydraulic fluid matching OEM specifications.
  • Periodically verify pump condition, alignment, and inspect hydraulic couplings for wear or leaks.
Key Specs at a Glance
  • Engine power: ~34 kW / 46.8 hp
  • Operating capacity: ~870 kg
  • Bucket capacity: 0.4 m³
  • Max discharge height: ~2.28 m
  • Travel speed: ~16 km/h
  • Weight: ~2.91 ton

Summary Table
  • Trouble Indicator: Poor performance under load or sluggish response
  • Likely Causes: Relief valve seating, air contamination, filter clogs, worn pump/components
  • Diagnostic Steps: Define symptom → gather operator logs → inspect filter/fluid → bleed system → test performance
  • Preventive Actions: Regular fluid & filter change, bleeding, pump maintenance, coupling inspection
With proper diagnosis, hydraulic system upkeep, and attention to pressure control components, the Komatsu SK818 can continue delivering reliable performance for years.
Reply


Messages In This Thread
Komatsu SK818 Troubles and Solutions - by MikePhua - 08-23-2025, 05:53 PM

Possibly Related Threads…
Thread Author Replies Views Last Post
  ChatGPT said: Kobelco SK135 Stalling Problem: Causes and Solutions MikePhua 0 6 24 minutes ago
Last Post: MikePhua
  John Deere 244E Transmission Problems: Troubleshooting and Solutions MikePhua 0 9 32 minutes ago
Last Post: MikePhua
  Oil Leaks in Cold Weather on the Kobelco ED150: Causes and Solutions MikePhua 0 10 36 minutes ago
Last Post: MikePhua
  Terramite T5C Shifting Issues and Solutions MikePhua 0 8 42 minutes ago
Last Post: MikePhua
  Gehl 4635 SX Skid Steer Hunting: Causes and Solutions MikePhua 0 8 48 minutes ago
Last Post: MikePhua
  Takeuchi T015 Control Pattern Switch: Troubleshooting and Solutions MikePhua 0 9 49 minutes ago
Last Post: MikePhua
  CAT 350L Excavator Troubleshooting and Solutions MikePhua 0 10 50 minutes ago
Last Post: MikePhua
  Diagnosing Rough Idle and Black Exhaust Smoke on a Komatsu D65PX-15 MikePhua 0 7 59 minutes ago
Last Post: MikePhua
  John Deere 200LC Swing Grease Seal: Issues and Solutions MikePhua 0 5 5 hours ago
Last Post: MikePhua
  ChatGPT said: Transmission Filter Issues in Terex 72-31 BA: Diagnosis and Solutions MikePhua 0 7 5 hours ago
Last Post: MikePhua
  Converting a Komatsu PC75UU-2 Offset Boom to a Standard One-Piece Boom MikePhua 0 11 5 hours ago
Last Post: MikePhua
  Komatsu D21A-6 Powershift Hesitation: Diagnosing and Solving Shifting Delays MikePhua 0 11 5 hours ago
Last Post: MikePhua
  Lift Pump Issues in Bobcat 743: Common Causes and Solutions MikePhua 0 3 5 hours ago
Last Post: MikePhua
  CAT 315B Monitor Problems and Solutions MikePhua 0 2 6 hours ago
Last Post: MikePhua
  Manifold Block Filter Issues in the SK120: Troubleshooting and Solutions MikePhua 0 6 6 hours ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)