Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Ex-60-1 Smoking Hydraulic Pump: Troubleshooting and Solutions
#1
In this thread, a user shares their experience with a smoking hydraulic pump on their Ex-60-1 excavator, seeking advice on potential causes and solutions. The problem described involves the hydraulic pump overheating and emitting smoke, leading to concerns about its functionality and safety. Through suggestions from various forum members, the thread delves into common causes of hydraulic pump issues and how to address them.
The Problem: Smoking Hydraulic Pump
The user reports that their Ex-60-1 excavator's hydraulic pump started smoking after extended use. This issue prompted concern as the pump was showing signs of overheating. The user expressed their worry about the pump potentially being damaged and the machine becoming unsafe to operate. They described the condition as persistent smoking, especially when the excavator was working for long periods or under load.
Initial Checks and Observations
Initially, the user performed a few basic checks to identify any obvious problems. They inspected the hydraulic fluid levels, ensuring that the fluid wasn’t too low, which could lead to pump overheating. The user also checked the quality of the hydraulic fluid, as dirty or contaminated fluid could cause the pump to malfunction or overheat. However, these initial checks did not solve the issue.
The user also observed that the hydraulic fluid was slightly foamy when inspected, which could suggest air contamination in the system. Air in the hydraulic system can reduce the effectiveness of the pump and cause it to overheat, resulting in smoking.
Possible Causes and Suggestions from Forum Members
Several forum members shared their experiences and advice on potential causes of the smoking hydraulic pump. Here are the main suggestions provided:
  1. Air in the Hydraulic System
    Many users pointed out that air trapped in the hydraulic system is a common cause of pump overheating. Air contamination can occur due to leaks in the suction side of the system, such as faulty seals, loose fittings, or cracks in the hoses. The presence of air in the hydraulic fluid can cause cavitation, which leads to a decrease in the hydraulic fluid’s ability to lubricate and cool the pump, resulting in overheating and smoke.
  2. Clogged or Dirty Hydraulic Filter
    A clogged hydraulic filter was also suggested as a potential cause. If the filter becomes dirty or clogged, it can restrict the flow of hydraulic fluid, leading to increased pressure and overheating of the pump. This would explain the smoking and overheating symptoms. Replacing the filter or cleaning it thoroughly was recommended.
  3. Excessive Load on the Pump
    Some members mentioned that excessive load on the hydraulic system could cause the pump to overheat. If the excavator was consistently working beyond its capacity or operating under high pressure, the hydraulic pump could be under strain, resulting in smoke. Checking the load limits and ensuring the machine is not being overworked could help prevent pump damage.
  4. Incorrect Hydraulic Fluid
    Another suggestion was the possibility of using the wrong type of hydraulic fluid. Hydraulic fluid that is too thick or of poor quality can cause increased friction within the pump, leading to overheating. It was recommended that the user verify the specifications for the required hydraulic fluid and ensure that the correct fluid is being used.
  5. Faulty or Worn Pump
    A few forum members suspected that the hydraulic pump itself might be worn or faulty, especially if it had been in service for a long time. Worn-out pumps could lead to inefficiencies and overheating. In such cases, pump replacement or professional servicing might be necessary to restore proper functionality.
Further Troubleshooting Steps
The forum members suggested a few additional troubleshooting steps to help identify and resolve the issue:
  • Check for Leaks: Inspect the entire hydraulic system for any signs of leaks, particularly on the suction side, as air ingress could be causing the problem.
  • Replace the Hydraulic Filter: If the filter is clogged, replace it with a new one to restore proper fluid flow.
  • Inspect Hydraulic Lines: Check all hydraulic hoses and connections for damage or wear, which could contribute to air contamination or fluid restriction.
  • Check Fluid Temperature: If the hydraulic fluid is too hot, it can exacerbate the problem. Consider using an oil cooler if the system is overheating.
Conclusion: Addressing the Smoking Hydraulic Pump
The thread offers valuable insights into diagnosing and resolving the issue of a smoking hydraulic pump in an Ex-60-1 excavator. The problem could be due to several causes, including air contamination, clogged filters, excessive load, incorrect fluid, or a worn-out pump. By performing thorough checks on the hydraulic system, replacing damaged components, and ensuring the system operates within its capacity, the user can likely resolve the smoking issue.
This thread serves as a helpful guide for anyone encountering similar issues with hydraulic pumps, offering practical troubleshooting advice and solutions to prevent further damage and ensure safe operation of the excavator.
Reply


Possibly Related Threads…
Thread Author Replies Views Last Post
  Kobelco Blade Runner: Operation and Troubleshooting Guide MikePhua 0 1 18 minutes ago
Last Post: MikePhua
  Case CX160 Recoil Assembly: Troubleshooting and Repair Guide MikePhua 0 1 20 minutes ago
Last Post: MikePhua
  D3 Steering Clutch Issues – Troubleshooting and Solutions MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Troubleshooting and Repairing Front-End Loader Valve Leaks on B95-C Case Tractor MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Wiring a Solenoid Valve – A Guide for Proper Installation and Troubleshooting MikePhua 0 1 1 hour ago
Last Post: MikePhua
  JCB 190 Auxiliary Hydraulics Inoperable: Troubleshooting and Solutions MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Pettibone Extendo 88 Velocity Governor: Issues and Troubleshooting MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Troubleshooting Overheating Issues and Electric Fan Malfunctions on Case 490E Excavat MikePhua 0 1 1 hour ago
Last Post: MikePhua
  CAT 980H Won’t Go Into Gear: Troubleshooting and Solutions MikePhua 0 1 1 hour ago
Last Post: MikePhua
  CAT 320B Excavator Electronic Display Screen Problem: Diagnosis and Solutions MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Troubleshooting a Case 680CK that Won’t Go Forward: A Step-by-Step Guide MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Troubleshooting Power Loss in Bobcat S150: Common Causes and Solutions MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Changing Hydraulic Fluid: A Step-by-Step Guide for Proper Maintenance MikePhua 0 1 1 hour ago
Last Post: MikePhua
  JLG 860SJ Control Boxes: Troubleshooting and Solutions MikePhua 0 1 1 hour ago
Last Post: MikePhua
  Troubleshooting Genie TMZ50 Towable Boom Lift Issues MikePhua 0 1 1 hour ago
Last Post: MikePhua

Forum Jump:


Users browsing this thread: 1 Guest(s)