Yesterday, 02:23 PM
Overview of the Incident
In a demanding dredging project involving Caterpillar D6T and D6R dozers, two critical failures occurred within a month of operation:
Environmental Stressors and Their Impact
Dredging environments present a unique set of challenges for tracked equipment:
Several contributing factors were identified through field analysis and operator feedback:
Experienced operators and mechanics offered practical advice based on similar scenarios:
At the Port of Portland, D8 dozers used in pipeline dredging reportedly achieved less than 1,000 hours of undercarriage life—sometimes as low as 500 hours. Attempts to use rubber-tired dozers failed due to U-joint failures and reduced effectiveness in wet sand. This underscores the brutal nature of dredging work and the need for specialized maintenance strategies.
Case Study: Sand Point Naval Base Conversion
During the decommissioning of the Sand Point Naval Base, dozers pushed dredged spoil through containment areas filled with slurry. Operators reported that undercarriage life was measured in months, not hours. The slurry often submerged tracks entirely, and the abrasive mix of sand and water led to rapid component degradation.
Industry Trend: Factoring Wear into Operational Costs
Fleet managers increasingly factor accelerated wear into hourly operating costs. In high-abrasion environments, budgeting for frequent undercarriage replacement is essential. Some operators even schedule mid-life replacements of segments and carrier rollers to extend overall system life.
Recommendations for Future Operations
To improve reliability and reduce downtime in dredging environments:
Dredging operations are among the harshest environments for tracked equipment. The failures of the D6T and D6R underscore the importance of adapting maintenance and operational strategies to match environmental realities. With the right combination of component selection, operator training, and preventive practices, even the most abrasive conditions can be managed effectively.
In a demanding dredging project involving Caterpillar D6T and D6R dozers, two critical failures occurred within a month of operation:
- The D6T experienced a broken track chain
- The D6R lost most of its track rollers
Environmental Stressors and Their Impact
Dredging environments present a unique set of challenges for tracked equipment:
- Abrasive Sand
Fine sand particles act like sandpaper, accelerating wear on chains, rollers, and bushings.
- Saltwater Exposure
Saltwater promotes corrosion, especially in seals and bearing surfaces, weakening structural integrity.
- Continuous Operation
Extended runtimes without adequate cooling or maintenance cycles increase thermal stress and mechanical fatigue.
- Track Packing and Tensioning
Wet sand can pack tightly between track components, increasing tension and potentially causing chain links to bind or break.
- Track Chain: A series of interconnected links that form the continuous track loop, transmitting motion from the sprocket to the ground.
- Track Roller: Cylindrical components that support the track chain and guide its movement along the undercarriage.
- LGP (Low Ground Pressure): A configuration with wider track shoes designed to distribute weight over a larger area, reducing ground pressure.
- Center-Punched Shoes: Track shoes with relief holes to allow packed material like sand or snow to escape, reducing tension buildup.
Several contributing factors were identified through field analysis and operator feedback:
- Pre-existing Wear
Although the chains were not new, they were considered in “good condition.” However, prior wear may have reduced their tolerance to extreme conditions.
- High-Speed Operation
Use of third gear, especially in reverse, increases dynamic loads on the undercarriage. High-speed travel in abrasive environments accelerates wear and increases the risk of component failure.
- Improper Track Tension
Over-tightened tracks in wet sand can cause excessive pressure on bushings and sprockets, leading to chain separation or roller damage.
- Component Quality and Compatibility
While genuine Caterpillar parts were used, the interaction between new rollers and older chains may have introduced uneven wear patterns.
Experienced operators and mechanics offered practical advice based on similar scenarios:
- Run Tracks Slack in Sand
Looser track tension allows sand to escape and reduces binding. Over-tight tracks in wet sand can cause bushings to seize and chains to snap.
- Avoid High Gear in Dredging
Operating in lower gears reduces stress on the undercarriage and improves traction in loose or saturated material.
- Use Center-Punched Shoes
These allow sand to extrude from the track system, minimizing buildup and reducing tension spikes.
- Monitor Operator Behavior
Observing operators when they’re unaware of supervision can reveal habits like excessive speed or aggressive maneuvering that contribute to wear.
At the Port of Portland, D8 dozers used in pipeline dredging reportedly achieved less than 1,000 hours of undercarriage life—sometimes as low as 500 hours. Attempts to use rubber-tired dozers failed due to U-joint failures and reduced effectiveness in wet sand. This underscores the brutal nature of dredging work and the need for specialized maintenance strategies.
Case Study: Sand Point Naval Base Conversion
During the decommissioning of the Sand Point Naval Base, dozers pushed dredged spoil through containment areas filled with slurry. Operators reported that undercarriage life was measured in months, not hours. The slurry often submerged tracks entirely, and the abrasive mix of sand and water led to rapid component degradation.
Industry Trend: Factoring Wear into Operational Costs
Fleet managers increasingly factor accelerated wear into hourly operating costs. In high-abrasion environments, budgeting for frequent undercarriage replacement is essential. Some operators even schedule mid-life replacements of segments and carrier rollers to extend overall system life.
Recommendations for Future Operations
To improve reliability and reduce downtime in dredging environments:
- Use center-punched shoes to relieve packed sand
- Run tracks looser than standard tension guidelines
- Avoid high-speed operation, especially in reverse
- Schedule frequent inspections and mid-life component replacements
- Train operators on terrain-specific techniques and wear mitigation
Dredging operations are among the harshest environments for tracked equipment. The failures of the D6T and D6R underscore the importance of adapting maintenance and operational strategies to match environmental realities. With the right combination of component selection, operator training, and preventive practices, even the most abrasive conditions can be managed effectively.
