On Panswork, a user described issues with their JCB Skid Steer HEP (Hydraulic Equipment Power) during operation, particularly concerning the hydraulic system and drive control. The user asked if others had encountered similar problems and sought advice on potential solutions and troubleshooting directions. The discussion revolved around resolving performance issues, especially in the hydraulic system and power control.
Problem Description
The user reported that their JCB Skid Steer HEP would experience instability in both the hydraulic system and drive control, causing uneven operation or loss of power. The machine sometimes faced power transmission issues, or there were significant fluctuations in hydraulic pressure, affecting work efficiency. The user mentioned checking the hydraulic fluid and control circuits, but the problem persisted.
Possible Causes of the Issue
In the Panswork discussion, multiple users suggested several potential causes for the JCB Skid Steer HEP problems:

1. Hydraulic System Faults
   Hydraulic system malfunctions are a common cause of performance issues. Some users speculated that problems with the hydraulic pump, hoses, or valves might be causing unstable system pressure, which affects the machine's power output. If the hydraulic oil is contaminated or the hydraulic filter is clogged, it can also decrease system efficiency.
   
2. Electrical System Problems
   The electrical control system might also be contributing to the issue. Faulty control circuits or malfunctioning sensors could prevent the power system from working properly. Some users believed that loose connections or faulty wiring in the machine’s electrical system could be affecting the hydraulic system's operation.
   
3. Hydraulic Oil Issues
   The quality and level of hydraulic oil are crucial to the machine’s performance. If the hydraulic oil is contaminated or the oil level is too low, the hydraulic system will not function correctly, causing power loss or decreased efficiency. Users recommended regularly checking the hydraulic oil’s condition and ensuring it meets the required standards for operation.
   
4. Overload or Overheating Problems
   Some users noted that overloads or overheating could contribute to power and hydraulic system problems. When the hydraulic system operates beyond its capacity, it could cause pressure fluctuations, leading to power issues. If the hydraulic system overheats, an overload protection mechanism may kick in, causing the machine to shut down.
   

1. Check the Hydraulic System
   Regularly inspect the hydraulic oil for cleanliness and ensure the oil level is correct. If the oil is contaminated or too low, replace or top up the hydraulic fluid. Inspect the hydraulic pump and valves to ensure proper functioning and avoid pressure fluctuations.
   
2. Inspect the Electrical System
   Check the electrical connections for any loose or damaged wiring. Ensure all sensors and control modules are working properly. If electrical issues are identified, repair or replace the faulty components.
   
3. Avoid Overloading
   Avoid operating the hydraulic system under overload conditions for extended periods. Regularly check the hydraulic system temperature to ensure it remains within the normal operating range and prevent overheating.
   
4. Perform Regular Maintenance
   Regular maintenance of both the hydraulic and electrical systems is essential. Inspect filters and hoses, and clean or replace any components that are worn or clogged.
   

1. Overview
On the Panswork forum, a user discussed the performance and applications of the Skat Trak 1700HD compact track loader. The Skat Trak 1700HD is a high-performance tracked loader, particularly suitable for working in tight spaces and rough terrains. It offers excellent pushing power and maneuverability, making it widely used in construction, land clearing, and farming operations.
2. Key Features of the Skat Trak 1700HD

1. High Maneuverability
   The Skat Trak 1700HD is equipped with a tracked system, which allows it to maintain excellent maneuverability on various challenging terrains. It is especially useful on soft or slippery surfaces, where wheeled loaders may get stuck.
   
2. Powerful Pushing Capability
   The design of this compact track loader enables it to handle substantial pushing forces, making it ideal for heavy-duty tasks such as pushing dirt, clearing debris, and land leveling. Even on tough surfaces, the Skat Trak 1700HD performs with impressive power.
   
3. Compact Design
   Compared to other similar machines, the Skat Trak 1700HD is relatively small in size, making it ideal for operations in narrow spaces. Its compact design allows for greater flexibility in urban construction or other environments with space constraints.
   
4. Comfortable Operation
   The operator's cab of the Skat Trak 1700HD is designed with comfort in mind. It features an advanced suspension system and adjustable seating to reduce vibrations, ensuring comfort during long working hours.
   

1. Lack of Power
   Some users have reported a lack of power during operation. Common causes could include issues with the fuel system or a clogged air filter. Checking the fuel system to ensure no blockages and cleaning or replacing the air filter may help restore normal power.
   
2. Loose Tracks
   After prolonged use, the tracks may become loose. It’s important to check the track tension and ensure it is set correctly. Regular inspection of track wear is also key to preventing issues.
   
3. Hydraulic Leaks
   Hydraulic system leaks can cause instability in operation. Regularly inspect hydraulic hoses and connections to ensure they are free from damage or cracks. If a leak is detected, promptly replace any faulty components.
   

1. Regularly Check Hydraulic Oil and Filters
   A key part of maintaining the hydraulic system is regularly checking the hydraulic oil quality and levels. Replacing the hydraulic oil and cleaning or replacing filters can help ensure efficient operation of the hydraulic system.
   
2. Keep Tracks Clean
   Since the Skat Trak 1700HD often operates in harsh conditions, the tracks can be affected by dirt and debris. Regularly cleaning the tracks to keep them in optimal condition will improve the longevity of the machine.
   
3. Check the Cooling System
   Regularly check the cooling system to ensure the radiator is clean and free from obstructions, and that the coolant levels are adequate. Preventing the machine from overheating will extend the engine life and maintain stable performance.
   

On Panswork, a user reported issues with their 2005 Bobcat S250 skid steer during operation. Specifically, the machine would start but fail to maintain stable operation, with the engine frequently stalling. The user also mentioned that the equipment would sometimes lose power suddenly, preventing continued work. This issue sparked a broader discussion, with several users sharing their own experiences and offering potential solutions.
Problem Description
The user described their 2005 Bobcat S250 not being able to keep running after startup, with the engine stalling frequently. At times, the machine would lose power unexpectedly, rendering it unable to continue operating. The user inspected the battery, fuel system, and air filter, but the problem persisted.
Possible Causes of the Issue
In the discussion on Panswork, several users suggested possible causes for the issue with the Bobcat S250:

1. Fuel System Problems
   Fuel system malfunctions are a common cause of stalling and loss of power. Some users speculated that a malfunctioning fuel pump, injectors, or fuel filter could be the culprit, causing unstable fuel delivery. If the fuel filter is clogged or the fuel pump’s efficiency drops, the machine may experience power loss or stall.
   
2. Electrical System Problems
   Another potential cause is an issue with the electrical system. Low battery voltage or poor electrical connections could prevent the machine from maintaining stable operation. Battery wear or loose wiring could result in the machine not keeping consistent power after starting.
   
3. Air Filter Issues
   The air filter plays a critical role in engine performance. If the air filter becomes clogged, the engine may not get enough air for combustion, leading to power loss or stalling. Users suggested checking the air filter, particularly if the machine operates in dusty environments.
   
4. Cooling System Problems
   Some users pointed out that issues with the cooling system might cause the machine to shut down unexpectedly or lose power. Low coolant levels or a clogged radiator could lead to overheating, triggering an automatic shutdown to protect the engine.
   

1. Check and Replace the Battery
   Ensure that the battery has sufficient voltage and inspect electrical connections for any loose or damaged wiring. If the battery is old or the voltage is low, replacing it is recommended to ensure proper startup and continued operation.
   
2. Inspect the Fuel System
   Check the fuel filter, fuel pump, and injectors to make sure fuel is being delivered properly. If the fuel pump or filter is faulty, replace them. Also, inspect the fuel lines for blockages or leaks.
   
3. Check the Air Filter
   Regularly inspect the air filter to ensure it isn’t clogged with dust or debris. If the air filter is dirty, clean or replace it to ensure the engine receives enough airflow for proper combustion.
   
4. Inspect the Cooling System
   Check coolant levels and inspect the radiator for blockages. If the coolant level is low, refill it; if the radiator is clogged, clean or replace it to prevent overheating.
   

1. Issue Overview
On the Panswork forum, a user raised concerns about the engine RPM range on their Case XT skid steer loader. The user reported that the engine’s RPM is not reaching the normal range, which is affecting the overall performance of the machine. This issue could be related to engine adjustments, fuel system issues, or failures in other related components, requiring detailed troubleshooting.
2. Common Causes

1. Fuel System Issues
   • If there is a problem with the fuel system, such as a faulty fuel pump, a clogged fuel filter, or insufficient fuel pressure, the engine RPM may not reach its normal range. These issues can disrupt fuel delivery, thereby affecting engine performance.
     
2. Clogged Air Filter
   • A clogged air filter can prevent the engine from receiving adequate air, which will affect the combustion process. Insufficient airflow can cause the engine RPM to drop, preventing it from performing optimally.
     
3. Engine Adjustment Issues
   • There could be problems with the engine’s adjustment system, such as the throttle or fuel injection system, which can lead to improper RPM ranges. This may involve issues with the throttle, fuel injectors, or the electronic control module (ECM).
     
4. Electrical System Malfunctions
   • A malfunction in the electrical system of the Case XT skid steer loader could also impact engine RPM control. Issues with sensors or feedback circuits may interfere with the RPM control, causing irregular engine speeds.
     

1. Check the Fuel System
   • Inspect the fuel pump, fuel filter, and fuel pressure to ensure they are working correctly. If there are any blockages or malfunctions, clean or replace the parts as needed.
     
2. Check the Air Filter
   • Examine the air filter to check for clogs. If the filter is dirty or blocked, clean or replace it to ensure proper airflow to the engine.
     
3. Check Engine Adjustment System
   • Verify the throttle and fuel injection system. Use diagnostic tools to check whether the electronic control module (ECM) is functioning properly, and ensure the engine’s adjustment system is operating as designed.
     
4. Check the Electrical System
   • Inspect the electrical system for issues related to the sensors and wiring connected to engine RPM control. Ensure that all sensors are providing correct feedback and that no electrical faults are present.
     

On Panswork, a user reported an issue with their AVS HD 4520 heavy equipment suddenly shutting down while operating. The user explained that the machine suddenly stalled during normal operation and couldn't be restarted, causing a work stoppage. This issue led to a broad discussion with many users sharing their experiences, discussing possible causes, and offering solutions for resolving the problem.
Problem Description
The user described the equipment suddenly shutting down while running. Although the fuel system, cooling system, and electrical system appeared to be in good condition, the machine could not be restarted after stalling. The user checked the starter battery, electrical connections, and fuel system, but the problem persisted. Upon further testing, the user found that the equipment was completely unresponsive.
Possible Causes of the Issue
In the discussion, users suggested several possible causes for the sudden shutdown of the AVS HD 4520:

1. Fuel System Issues
   Fuel system problems are a common cause of machine stalling. Some users speculated that a malfunctioning fuel pump or injectors could be preventing proper fuel delivery. If the fuel filter or fuel lines are clogged, the machine may fail to operate normally.
   
2. Electrical System Problems
   Another common issue is electrical system failure, which includes low battery voltage, loose electrical connections, or short circuits. If the battery voltage is low or there is a problem with the wiring, the equipment could suddenly shut down during operation and may not restart.
   
3. Sensor Malfunction
   Some users pointed out that sensor malfunctions might also cause the equipment to stall. For instance, if the Engine Control Module (ECM) sensors detect incorrect signals, they might shut off fuel delivery or stop the engine to protect the machine. Checking the functionality of the sensors is an essential step in diagnosing the issue.
   
4. Overheating Problems
   Overheating during extended operation could cause the engine to automatically shut down to prevent damage. Some users believed that a malfunctioning cooling system, such as low coolant levels or a clogged radiator, might lead to overheating and trigger the shutdown.
   

1. Check and Replace the Battery
   Ensure that the battery voltage is adequate and check the electrical connections for any loose or damaged wiring. If the battery is old or the voltage is low, it’s recommended to replace it to ensure proper startup and operation.
   
2. Inspect the Fuel System
   Check the fuel filter, fuel pump, and injectors to ensure proper fuel delivery. If the fuel pump or filter is faulty, replace them. Also, check the fuel lines for any blockages or leaks.
   
3. Check the Sensors and ECM
   Use diagnostic tools to check the Engine Control Module (ECM) and sensors for any faults. If error codes are found, further analysis should be done, and faulty sensors should be replaced.
   
4. Inspect the Cooling System
   Check the coolant levels and radiator for any issues. If the radiator is clogged or the coolant levels are low, it’s important to address these problems to prevent overheating and engine shutdown.
   

1. Issue Overview
On the Panswork forum, a user reported issues with the auxiliary electrical plug on their Bobcat T190 skid-steer loader. The user stated that their machine is unable to properly connect to auxiliary equipment, with the electrical plug not functioning correctly or failing to work altogether. This issue is likely related to electrical connections or a damaged plug, and it requires troubleshooting to identify and resolve.
2. Common Causes

1. Damaged Electrical Plug
   • The auxiliary electrical plug on the Bobcat T190 may be damaged due to extended use or frequent connecting and disconnecting. The contact points of the plug may suffer from corrosion or wear, preventing a proper electrical connection.
     
2. Loose Electrical Connections
   • If the plug is not securely connected to the machine’s electrical interface, it can cause signal loss or insufficient power, preventing the auxiliary function from operating. Loose electrical connections are a common cause of failure in these types of systems.
     
3. Incompatible Plug with Equipment
   • Users may encounter situations where the electrical plug is not compatible with equipment from different brands or models. The electrical interface of certain equipment may not align with the standard plug used by the Bobcat T190, leading to connection issues or non-functionality.
     
4. Electrical System Failure
   • A failure in the electrical system of the Bobcat T190, such as issues with the electrical control module, wiring, or fuses, can also prevent the auxiliary electrical plug from working. A full inspection of the electrical system is necessary to rule out any potential faults.
     

1. Check the Plug and Electrical Connections
   • Perform a visual inspection of the electrical plug and connections, looking for signs of damage, wear, or corrosion. If any issues are found, clean the contacts or replace the plug to restore proper functionality.
     
2. Ensure a Secure Connection
   • Inspect the connection between the plug and the electrical interface to make sure there is no looseness or poor contact. Reconnect or securely fasten the plug to ensure a tight fit.
     
3. Check Compatibility
   • If you are using third-party equipment or attachments, check whether the plug is compatible with the Bobcat T190’s standard electrical interface. If it is incompatible, you may need to replace the plug or use an adapter to make it work.
     
4. Inspect the Electrical System
   • If the plug appears to be fine, move on to inspecting the entire electrical system of the Bobcat T190. Check the electrical control module, wiring, fuses, and other components to ensure everything is functioning correctly. If any faults are found, address them accordingly.
     

On Panswork, a user shared their experience with the Bobcat 751 skid steer encountering several issues, particularly with starting and power loss. The machine had difficulty starting, especially in colder weather, and even when it did start, the engine's performance was below expectations, leading to reduced efficiency. This sparked a broad discussion, with many users sharing their own experiences and solutions to help others diagnose and fix similar problems.
Common Issues and Symptoms
The most commonly reported problems with the Bobcat 751 included difficulty starting and power loss. Users noted that the machine struggled to start, particularly in cold weather. Even when it did start, the engine’s performance was far from ideal, with insufficient power output, which affected normal operation. Some users also mentioned that after starting, the machine would run unevenly and sometimes even stall.
Possible Causes of the Issue
Here are some of the potential causes discussed by users that could lead to these problems:

1. Battery and Electrical System Failures
   Many users believe that the difficulty starting the machine is related to insufficient battery voltage or electrical system faults. The Bobcat 751 may struggle to start if the battery is old or has been used for a long time, leading to inadequate starting voltage. Without sufficient current from the battery, the machine may either fail to start or fail to run properly once it starts.
   
2. Fuel System Problems
   Fuel supply issues are another common cause of engine starting problems. Some users found that a clogged fuel filter, faulty fuel pump, or malfunctioning fuel injectors could all affect engine startup and performance. Any issue in the fuel system can lead to unstable fuel delivery, impacting the engine's normal operation.
   
3. Air Filter and Intake System Issues
   A clogged air filter or a leaking intake system can cause insufficient airflow to the engine, affecting its combustion efficiency. Some users mentioned that when the air filter is dirty or blocked, the engine can’t get enough air, leading to difficulty starting and reduced power.
   
4. Cold Starting Issues
   Some users pointed out that the Bobcat 751 has difficulty starting in low temperatures, especially in colder climates. Cold starting problems are often linked to inadequate engine preheating or oil that is too thick, making it harder for the engine to start or leading to stalling.
   

1. Check the Battery and Electrical System
   Ensure that the battery has sufficient voltage and check the electrical connections for any loose or damaged wiring. Users recommended regular inspection of the battery and electrical system, especially before cold weather, to ensure enough starting current is available.
   
2. Clean or Replace the Fuel Filter
   Check and replace the fuel filter to ensure smooth fuel delivery. If issues with the fuel pump or injectors are found, they should be repaired or replaced to restore proper fuel system functionality.
   
3. Replace the Air Filter
   Regularly inspect the air filter to ensure it isn’t clogged with dust or debris. If the air filter is dirty, it should be replaced to maintain airflow and ensure the engine runs efficiently.
   
4. Use Appropriate Oil for Cold Weather
   For cold starting issues, users suggested using oil that is suitable for colder temperatures, as this reduces the oil’s viscosity, making it easier for the engine to start.
   

1. Issue Overview
On the Panswork forum, a user reported electrical issues with their Bobcat 863 skid-steer loader, causing the auxiliary hydraulic function to be inoperative. Specifically, while the main hydraulic system functions normally, the auxiliary hydraulic system fails to activate. This issue likely stems from a problem with the electrical system, and it requires troubleshooting and resolution.
2. Common Causes

1. Electrical Connection Issues
   • Loose or poor electrical connections can prevent the auxiliary hydraulic system from receiving the necessary electrical signals to operate. Common problem areas include connectors, terminals, and switches that may suffer from corrosion, wear, or looseness.
     
2. Low Battery Voltage
   • Insufficient battery voltage or a failing battery can disrupt the electrical system, preventing power from reaching various components, including the auxiliary hydraulics. Check the battery's voltage and condition to ensure it is providing adequate power.
     
3. Blown Fuses or Faulty Relays
   • The auxiliary hydraulic system may rely on specific fuses or relays for operation. If any of these components are blown or faulty, they can interrupt the electrical signal flow, preventing the auxiliary hydraulics from activating. Inspect and replace any damaged fuses or relays.
     
4. Faulty Electrical Control Module
   • The Bobcat 863 may have a malfunctioning electrical control module (ECM), which is responsible for transmitting electrical signals to the auxiliary hydraulic system. If the ECM is not functioning correctly, it could fail to send the proper signals. In this case, the ECM may need to be repaired or replaced.
     
5. Shorted or Damaged Wiring
   • Damaged or short-circuited electrical wires can disrupt the flow of electrical signals, preventing the auxiliary hydraulics from operating. A thorough inspection of the wiring is necessary to identify any faults.
     

1. Check Electrical Connections
   • Inspect all electrical connections, including connectors, terminals, and switches, for any loose or corroded parts. If any issues are found, clean or reconnect the components to ensure proper electrical contact.
     
2. Check Battery Voltage
   • Use a multimeter to check the battery voltage to ensure it is within the correct range for starting the electrical system. If the voltage is low, recharge the battery or replace it if necessary.
     
3. Inspect Fuses and Relays
   • Refer to the user manual to locate the fuses and relays that control the auxiliary hydraulics. Check for any blown fuses or faulty relays and replace them as needed.
     
4. Check the Electrical Control Module
   • If the problem persists, the ECM may be at fault. Use diagnostic tools to check for any error codes or malfunctions. If the ECM is identified as faulty, consider repairing or replacing it.
     
5. Inspect Electrical Wiring
   • Carefully inspect the electrical wiring for signs of damage, short circuits, or wear. Repair or replace any damaged wiring to restore proper signal transmission.
     

In a discussion on Panswork, a user reported an issue with their CAT 246D skid steer where oil was found in the antifreeze reservoir. This type of problem usually indicates an internal fault within the machine’s cooling system or engine, potentially leading to more serious damage if not addressed. The issue sparked a broad conversation about the causes and solutions for this kind of problem, with many users sharing their experiences and advice for diagnosing and fixing the issue.
Cause Analysis
The presence of oil in the antifreeze reservoir typically results from one of the following causes:

1. Oil Cooler Leak
   The CAT 246D is equipped with an oil cooler, which uses coolant to help regulate the temperature of the engine oil. If the oil cooler leaks, engine oil and coolant can mix, leading to oil appearing in the antifreeze reservoir. This is one of the most common causes of this issue, as the oil cooler operates under high heat and pressure, making it prone to cracks or corrosion.
   
2. Engine Seal Failure
   Another potential cause is a failure in the engine’s internal seals. If the seals on components such as the water pump or oil pump fail, oil and coolant can mix through leaks. While less common, this issue can cause oil to enter the coolant system.
   
3. Heat Exchanger Failure
   In some cases, a faulty heat exchanger can cause direct mixing of coolant and engine oil. Although rare, if the heat exchanger fails, it may allow oil and coolant to pass into each other's systems.
   

1. Replacing the Oil Cooler
   Most users recommended inspecting and replacing the oil cooler, as this is often the primary cause of coolant and oil mixing. Checking for cracks or signs of corrosion in the oil cooler is essential, and replacing it with a new one is usually necessary to restore the system to normal operation.
   
2. Inspecting Engine Seals and Pumps
   If the oil cooler appears intact, the next step should be to check the engine seals, particularly those on the water pump and oil pump. If any seals are found to be damaged, replacing them is crucial to prevent further oil and coolant mixing.
   
3. Changing Oil and Coolant
   Once the oil cooler or seals are replaced, it’s important to change both the engine oil and coolant. This will clear out any contaminants that may have entered the systems and ensure that both the engine and cooling system are operating properly.
   

1. Issue Overview
On the Panswork forum, a user reported an issue with their 2007 CAT 262C skid-steer loader, where the bucket curl function does not hold its position. Specifically, after initially curling the bucket, it slowly uncurls and does not maintain the desired position. This issue can affect operational efficiency and safety, and it is important to diagnose and fix it promptly.
2. Common Causes

1. Hydraulic System Leaks
   • If there are leaks in the hydraulic system, hydraulic fluid will be lost, which can cause insufficient pressure to maintain the bucket's position. Leaks can occur in hydraulic hoses, connections, or seals.
     
2. Hydraulic Cylinder Seal Failure
   • The seals inside the hydraulic cylinders may wear out or become damaged over time, leading to hydraulic fluid leakage. This results in insufficient pressure to maintain the bucket’s position. Signs of seal failure include external oil residue on the cylinder or insufficient pressure inside the cylinder.
     
3. Hydraulic Pump or Control Valve Failure
   • The hydraulic pump is responsible for generating the pressure, while the control valve regulates the flow of hydraulic fluid. If either of these components malfunctions, it may fail to provide adequate pressure or flow, resulting in the bucket not holding its position or functioning as expected.
     
4. Poor Hydraulic Oil Quality
   • The quality of hydraulic oil is crucial to the performance of the hydraulic system. Using low-quality or contaminated hydraulic oil can cause the system to operate inefficiently, which can affect the bucket's control and stability.
     

1. Check for Hydraulic Leaks
   • First, inspect the entire hydraulic system for leaks, especially around hoses, fittings, and seals. Use a pressure gauge to check for leaks or drops in pressure. If a leak is found, replace the damaged parts immediately to restore proper pressure.
     
2. Inspect Hydraulic Cylinder Seals
   • Check the seals in the hydraulic cylinders, particularly the piston and rod seals, for signs of wear or damage. If the seals are compromised, they will need to be replaced to prevent hydraulic fluid leakage and restore pressure.
     
3. Check Hydraulic Pump and Control Valve
   • Ensure that the hydraulic pump is producing the correct pressure, and verify that the control valve is operating correctly. A faulty pump or valve can cause insufficient hydraulic flow, which will affect the bucket’s function. If either component is malfunctioning, repair or replace it.
     
4. Check Hydraulic Oil Quality
   • Inspect the hydraulic oil to ensure it is clean and meets the required specifications. If the oil is dirty, contaminated, or the level is low, drain and replace the oil with fresh, high-quality hydraulic fluid.